Whirlpool Cassinetta Repair Manual Line Download Page 52

Page: 52 / 78

Troubleshooting & Diagnostic:

Communication failure indication “CF” on the freezer display

What you have to check for bad connections:

PINS:



DAMAGED



DIRTY



NOT PROPERLY
INSERTED

CONNECTORS:



DAMAGED



DIRTY



BATHED



NOT PROPERLY
COUPLED

BOARD CONNECTORS:



CRUSHED



DIRTY



DIRTY PINS



NOT PROPERLY SOLDERED

WIRES:



CUTTED



BURNED

Communication failure between

Main Board and User Board.

Check

ALL

the connections (see pictures below)

Connections are all good? Pins are all inserted?

Replace the User Board and, if the problem

persist, replace the Main Board

Indication “UU” on the freezer

display

(only for 2007 range

appliances and following):

There is communication between

Main Board and User Board is

OK, but the boards are not

compatible. Check the board

codes and replace the wrong

board.

Summary of Contents for Cassinetta















































































Search results

Summary of Contents for Cassinetta

Reviews:

Related manuals for Cassinetta

Brands by name

Popular brands

Whirlpool Cassinetta, Repair Manual Line

Search results

Summary of Contents for Cassinetta

Reviews:

Related manuals for Cassinetta

Brands by name

Popular brands