Whirlpool Cassinetta Repair Manual Line Download Page 47

Page: 47 / 78

Anti-condensate function

Anti-condensate function on the door:
(ONLY for appliances with Inox doors)

Anticondensate

heater on the door?

Which appliances?

How to activate it?

NO heater

Biruni (IDI) + all no dispenser

appliances

YES heater

Biruni (NO IDI) + all the

previous ranges (except no

dispenser)

Achievable / de-achievable using

the switch on the user, see picture

below (normally ON from the

factory)

Anticondensate function on the user niche:

Anticondensate

heater on the User

niche?

Which appliances?

How to activate it?

NO heater

Biruni (IDI) + all no dispenser

appliances

YES heater

Biruni (NO IDI) + all the

previous ranges (IDI e NO

IDI)

Achievable / de-achievable using

the switch on the user, see picture

below (normally ON from the

factory)

Summary of Contents for Cassinetta















































































Search results

Summary of Contents for Cassinetta

Reviews:

Related manuals for Cassinetta

Brands by name

Popular brands

Whirlpool Cassinetta, Repair Manual Line

Search results

Summary of Contents for Cassinetta

Reviews:

Related manuals for Cassinetta

Brands by name

Popular brands