Whirlpool Cassinetta Repair Manual Line Download Page 66

Page: 66 / 78

Possible reason:

Door

gasket damaged or
deformed, air leakage
inside the appliance.

Check

ALL

the gaskets (freezer and fridge).

Only if a few deformation is detected, try to
repair it heating up the involved area and
modelling the gasket.

If the door gasket is damaged or not
repairable, substitute it.

Possible reason:

Door

ice cover bad closure, air
leakage inside the
appliance.

Check the white ice chute (see pictures
below). If too much protruding from the
housing, replace the door.

Note:

this issue could be more frequent on

appliance produced between w18 and w35
2008.

NOT OK

Troubleshooting & Diagnostic:

Ice formation and moisture in freezer compartment

See also the previous pages, ‘ice formation on freezer roof’ and

‘ice formation on freezer bottom’ chapter.

Summary of Contents for Cassinetta















































































Search results

Summary of Contents for Cassinetta

Reviews:

Related manuals for Cassinetta

Brands by name

Popular brands

Whirlpool Cassinetta, Repair Manual Line

Search results

Summary of Contents for Cassinetta

Reviews:

Related manuals for Cassinetta

Brands by name

Popular brands