Whirlpool Cassinetta Repair Manual Line Download Page 25 | Manualshive

Page: 25 / 78

background image

25

At the end of the Built-in Test it is possible to reset to “0” the Water Filter Indicator and/or
Antibacterial Filter Indicator in the following way:

-

Water Filter Indicator Factory/Service reset

Press 4 times consecutively (within 10 sec) the Water valve shaft switch.
The symbol “F” on the Refrigerator display shall be shown in order to confirm the operation.

-

Antibacterial Filter Indicator Factory/Service reset

Press 4 times consecutively (within 10 sec) the Refrigerator Compartment door switch.
The symbol “A” on the Refrigerator display shall be shown in order to confirm the operation.

Built-In Test check code (User Interface operation)

The check code will be displayed on the Fridge display. Every check will have the related check
code that will be the same as the sequence number foreseen during the Built-in Test.

ERROR TYPE

ERROR

CODE

NOTE

Components (Relay Damper)

8

Displayed on 1 digit Fridge display

Evaporator De-Frost heater

7

Displayed on 1 digit Fridge display

Fridge probe

6

Displayed on 1 digit Fridge display

Freezer probe

5

Displayed on 1 digit Fridge display

Evaporator fan

4

Displayed on 1 digit Fridge display

Compressor fan

3

Displayed on 1 digit Fridge display

Damper

2

Displayed on 1 digit Fridge display

Water valve dispenser

1

Displayed on 1 digit Fridge display

Ice valve

9

Displayed on 1 digit Fridge display

Ice Maker Sankyo

H

Displayed on 1 digit Fridge display

OPERATION TYPE

OPERATION

CONFIRMED

CODE

NOTE

Water Filter Indication reset
by Service/Factory

F

Displayed on 1 digit Fridge display

Antibacterial Filter Indication
reset by Service/Factory

A

Displayed on 1 digit Fridge display

If 2 or more errors code have been recognized these codes shall be displayed on fridge
display in a rolling way (each code will persist about 1 second till the Built-in Test will be
stopped).

«
...
23
24
25
26
27
...
»

Summary of Contents for Cassinetta















































































Reviews:

No comments

Related manuals for Cassinetta

Brand: Daewoo Pages: 12

Brand: Daewoo Pages: 11

Brand: NEFF Pages: 20

Brand: Blomberg Pages: 39

Brand: Engel Pages: 13

ChefLine CHPZ2P

Brand: CHEFOOK Pages: 102

790 Active Smart

Brand: Fisher & Paykel Pages: 59

CoolMatic HDC-160

Brand: Waeco Pages: 32

Brand: Medco Pages: 7

Brand: UNITED Pages: 22

Brand: Magic Chef Pages: 28

Gastronorm Supra

Brand: Foster Pages: 12

Brand: Zanussi Electrolux Pages: 20

Brand: Hotpoint Pages: 2

Brand: Samsung Pages: 38

Brand: Samsung Pages: 38

Brand: Samsung Pages: 38

Brand: Samsung Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands