manualshive.com logo in svg

WESTCAR ROTOMEC ALFA, Original Instructions Manual, Page: 73 / 84

Share
Download
WESTCAR ROTOMEC ALFA Original Instructions Manual Download Page 73

73

P

o w e r

  T

r a n s m i s s i o n

7.4   INSPECTION OF OVERHEATING CONTROL DEVICES

These mandatory inspections guarantee the correct operation of the overheating control devices, which 

are  installed  on  the.  hydromechanic  coupling.  They  must  take  place  regularly,  in  connection  with  the 

ORDINARY MAINTENANCE activities to monitor the conditions of the devices installed. To perform the 

inspection, please follow the described procedure:

CAUTION: 
Before you start checking devices:

A- stop the motor and wait for the rotation components to stop,

B- cut out power supply and apply a safety padlock,

C- signal the operation under way,

D- wait for the cooling, if needed (max 40°C).
7.4.1

Open the accident-prevention guard of the operating area to access the coupling.

7.4.2 TF DEVICE (Expandable Trip Plug)

PAD

  - Unscrew the TF and check the inside pad for deformation and damages.

 - Make sure that the TF is in good working order and its outside seat is not 

obstructed.

7.4.3 TE DEVICE (Expandable Trip Plug)

Ø4

Ø8

5 8

6

- Make sure that the TE device is not impaired and the 

piston is not deformed or blocked and the return spring 

is in good working order.

-  Make  sure  that  device  (safety  microswitch)  has  not 

been  tempered  with,  it  is  in  good  working  and  the 

distance between the detector and the device is 2 mm., 

 7.4.4 PM T09 UNIT

T09

PM

- Make sure that the PM device in the coupling is in good 

operating conditions it is not damaged. 

- Make sure that the sensor of the T09 device has not 

been tampered with, is in good operating conditions 

and  detecting  distance  is  between  2mm  and  5mm 

(see distance defined during test and inspection).

NOTE

The correct functioning of the PM-T09 combined unit is signalled by a yellow led, when the PM plug 

passes in front of the sensor.

7.4.5

Note in section 7.5 SERVICE RECORD the results of the operation and/or, if necessary, carry out the 

replacement or resetting of the overheat protection devices.

CAUTION

Do  not  use  fluid  couplings  without  devices  or  if  devices  have  been  tampered  with  or  are 

inefficient. DANGER OF OVERHEATING AND/OR FIRE IGNITION.
7.4.6

Remove any used key and/or cloth or tool from the coupling and the operating area. 

DANGER OF 

PHYSICAL INTERFERENCE.
7.4.7

Close the accident-prevention guard of the hydromechanic coupling operating area.

The check of the overheating control devices has thus ended

P

art

 7 - o

rdinary

 M

aintenance

ROTOMEC 

U

Se

 

and

 M

aintenance

 h

andbook

Summary of Contents for ROTOMEC ALFA





















































































Reviews:

No comments