WESTCAR ROTOMEC ALFA Original Instructions Manual Download Page 39

Page: 39 / 84

o w e r

r a n s m i s s i o n

4.2.5e

Sling the hydromechanic coupling on the hoisting device with ropes having a load

capacity suitable for its weight (see Identification Plate). Lift the coupling to a min-

imum height, approach it to the installation shaft with slow movements and fit it on

the taper sleeve of the motor.

CAUTION

Do not hit, bang about or exert any force on the coupling shells.

DANGER OF DAMAGING THE BEARING SEATS, CRACKINGS, VIBRATIONS

AND/OR UNBALANCE.

4.2.5f

Insert the retaining screw on the end of the shaft provided with a suitable washer

and screw it on the drive shaft.

4.2.5g

Tighten the central clamping screw, preventing any motion of the machine or motor shaft,

where it is mounted. For tightening, respect the torque values as reported in the table.

COUPLING SIZE

TAPER BUSH BC

RETAINING

SCREW

CLASS

TORQUE Nm

30 / 30P

3BC 54 D= ø28

3BC 54 D= ø38

3BC 54 D= ø42÷50

M10

M12

M16

8.8

210

40P

4BC 58 D= ø38÷40

4BC 58 D= ø40÷42

4BC 58 D= ø48÷50

M12

M16

8.8

210

50 / 55

5BC 73 D= ø38÷40

5BC 73 D= ø40÷50

5BC 73 D= ø55÷65

M12

M16

M20

10.9

8.8

120

210

230

60 / 65[B]

6BC 79,5 D= ø40÷50

6BC 79,5 D= ø55

6BC 79,5 D= ø60÷65

M16

M20

10.9

8.8

290

410

Coupling with taper bush without keyways

4.2.5f

4.2.5g

art

4 - i

nStallation

oMMiSSioning

ROTOMEC

and

aintenance

andbook

Summary of Contents for ROTOMEC ALFA





















































































Search results

Summary of Contents for ROTOMEC ALFA

Reviews:

WESTCAR ROTOMEC ALFA, Original Instructions Manual, Page: 39 / 84

Search results

Summary of Contents for ROTOMEC ALFA

Reviews: