manualshive.com logo in svg

WESTCAR ROTOMEC ALFA, Original Instructions Manual, Page: 34 / 84

Share
Download
WESTCAR ROTOMEC ALFA Original Instructions Manual Download Page 34

34

P

o w e r

  T

r a n s m i s s i o n

The standard ROTOMEC coupling (standard production) is delivered with hollow 

shaft and key seat according to DIN6885 standard for UNELMEC motors. The 

keying of the coupling (hollow shaft side) can be carried out on the motor (electric 

or endothermic) as well as on the machine driven end, according to the specific 

instructions reported on both the Identification Plate and the TECHNICAL DATA 

SHEET OF THE HYDROMECHANIC COUPLING.

STANDARD ASSEMBLY

Motor connected to the hollow shaft of the coupling (inner part)

VERTICAL ASSEMBLY

The  hydromechanic  coupling  produced  with  “C”  manufacture  is  designed  for 

vertical installation, in order to ease both the filling and the oil level calibration 

(see Identification Plate).

CAUTION

It is forbidden to install the hydromechanical coupling with the motor 

or the drive part connected to the outer shells of the coupling itself.

Following you can read by way of example the instructions for the coupling key-

ing (hollow shaft side) on the motor and/or machine.

4.2  FITTING OR ROTOMEC COUPLING ON DRIVE SHAFT

STANDARD MOUNTING

VERTICAL MOUNTING

ROTOMEC ALFA

ROTOMEC BETA

P

art

 4 - i

nStallation

 a

nd

 c

oMMiSSioning

ROTOMEC 

U

Se

 

and

 M

aintenance

 h

andbook

Summary of Contents for ROTOMEC ALFA





















































































Reviews:

No comments