manualshive.com logo in svg

Wenger Diva, Installation Instructions Manual, Page: 31 / 36

Share
Download
Wenger Diva Installation Instructions Manual Download Page 31

31

Light Fixture Configuration (continued)

Configure the DMXcat

®

 Connection

To configure the DMXcat

®

 device to communicate with the configuration tablet:

1.  Gently insert the DMXCat’s 5-pin 

 

XLR jack into the 5-Pin XLR panel 

 

mount plug with the protruding pins  

located on the light fixture control box.

2.  Turn on the configuration tablet, 

 

once the home screen is displayed  

select the appstore icon.

3.  Select the search icon in the upper  

corner of the screen, type “DMXcat” 

 

in the search bar then select the  

orange search icon, select “get” 

 

to download the DMXcat app by 

 

City Theatrical.

4.  Select the empty circle on the bottom  

of the screen to return to the tablet  

home screen, then select the DMXcat app.

5.  Once the app is open select the  

settings icon located in the top right  

corner of the screen, then select “device list” 

 

located under the bluetooth device section.

6.  Locate the required DMXcat serial number and 

 

select it to establish a connection between the  

configuration tablet and the device.

7.  The LED status indicator on the device will continuously illuminate green once the connection is established.

8.  Configure the fixture to the required DMX/RDM address based on the site’s requirements.

9.  If required, select and hold down the Link icon in the lower left corner of the screen to disconnect the 

DMXcat device from the configuration tablet. Wait for the LED status indicator to flash four times before 

disconnecting the device from the fixture.

10. If additional information is required select the DMXcat info icon to view the information provided by 

 

City Theatrical while using the configuration tablet.

Lieto LED Light Fixture Communication

The Lieto LED light fixture is compatible with the following communication networks:

•  ANSI E1.11-2008 (R2013) USITT DMX512-A

•  ANSI E1.20-2010 RDM over DMX512 Networks

•  ANSI E1.37-1-2012 Additional RDM Message Sets

The configurable settings are made via RDM commands, serial TTL commands, and the tablet programmer.
On-board fixture monitoring such as temperature, power cycles, and hours of operation are also continuously 

recorded.

Unpackaged DMXcat Connector 

(Kit components may vary slightly)

DMXcat 

XLR5F 

Connector

Belt Clip, Screw  

and  

Splint Ring Safety Point

USB to 

Micro USB 

Cable

XLR5M to 

XLR5M 

Turnaround

Summary of Contents for Diva





































Reviews:

No comments