manualshive.com logo in svg

Wenger Diva, Installation Instructions Manual, Page: 28 / 36

Share
Download
Wenger Diva Installation Instructions Manual Download Page 28

Black Truss 

Head Screw, 

8-18 x 5/8"

Light Trim 

Ring

Self-Drilling Screw, 

1/4-14 x 3/4"

Counter 

Weight

Lieto LED 

Light Fixture

Light 

Assembly  

Housing

Mounting 

Hole

Tri-Fold 

Blind Rivet,  

0.19 Dia.

28

Light Fixture Installation

Inspection

Before installing, inspect the light fixtures for any signs of damage. 

 

If any damages are present, immediately contact Wenger.

Lieto LED Light Fixture Installation

Install the light fixtures into the pre-cut ceiling panel holes. 

 

Refer to the installation drawings for locations.

A licensed electrician must perform the electrical installation.

Branch circuits that connect to ceiling panel lights must always be designed by an electrical 

engineer and comply with electrical codes and user requirements.

All electrical sources must be permanently wired and comply with local electrical codes.

Each ceiling panel light must connect to a grounded, three-wire receptacle that connects to a 

fused circuit breaker.

This procedure details installing the Lieto

™

 LED Light Fixture. 

If installing other light fixtures, contact Wenger.

STOP

!

WARNING

1.  Insert the light fixture into the pre-cut ceiling panel light mounting hole.

2.  Attach the light assembly to the ceiling panel.

a.  Use a 13/64" bit to drill a pilot hole through the upper panel surface only. 

 

Clean away any shavings from drilling.

b.  Attach the light to the panel using  

four 0.19 dia tri-fold blind rivets.

3.  Attach the trim ring to the bottom  

side of the ceiling panel with four  

black truss head screws, 8-18 x 5/8”. 

 

Do not over tighten the screws.

Drill through the upper panel surface only. 

Do not drill into the lower panel surface.

Do not over tighten the 

screws, damage to the  

panels could result.

!

CAUTION

!

CAUTION

4.  Attach an appropriate  

amount of counter weight  

to balance the row to the  

panel extrusion on the  

opposite side using  

two 1/4-14 x 1" self-drilling  

screws.

Summary of Contents for Diva





































Reviews:

No comments