background image

PERSONAL PROTECTION

 DANGER

All utilities (gas, electric, water and steam) must be  OFF 
to all equipment and locked out of operation according to 
OSHA approved practices during servicing. Always allow 
unit to cool.

 DANGER

Use appropriate safety equipment during installation and 
servicing.

 DANGER

Never stand on the unit! They are not designed to hold 
the weight of an adult, and may collapse or tip if misused 
in this manner.

 DANGER

Keep power cord AWAY from HEATED surfaces. DO NOT 
immerse power cord or plug in water. DO NOT let power 
cord hang over edge of table or counter.

n

Warning

DO  NOT  use  the  unit  for  storage.  DO  NOT  leave  paper 
products, cooking utensils, or food in the unit when not 
in use.

n

Warning

Allow heated equipment to cool down before attempting 
to clean, service or move. Unit must be cool to touch and 
disconnected from power source.

n

Warning

Always  wear  some  type  of  protective  covering  on  your 
hands and arms when opening the unit.

n

Warning

Steam can cause serious burns. Always wear some type 
of  protective  covering  on  your  hands  and  arms  when 
opening the unit. When platen is Lifting, move away face 
and body from the escaping steam.

n

Warning

Remove all removable panels before lifting and installing. 

n

Warning

Do not contact moving parts.

n

Warning

When  using  cleaning  fluids  or  chemicals,  rubber  gloves 
and eye protection  (and/or face shield) must be worn.

n

Warning

Use caution when handling all metal surface edges of the 
equipment.

n

Warning

This equipment is intended for indoor use only.  Do not 
install or operate this equipment in outdoor areas.

n

Warning

All covers and access panels must be in place and properly 
secured, before operating this equipment.

n

Warning

Do  not  spray  aerosols  in  the  vicinity  of  this  appliance 
while it is in operation.

n

Warning

Risk of burns from high temperatures. You may get burnt 
if you touch any of the parts during cooking.  Surfaces 
close to the cooking surface including side panels may 
get hot enough to burn skin. Use extreme caution to 
avoid coming in contact with hot  surfaces or hot grease. 
Wear personal protective equipment.

n

Warning

When  checking  for  burner  ignition  or  performance,  do 
not get too close to the burners. Slow ignition can cause 
possible flashback, increasing the potential for facial and 
body burns.

n

Warning

This appliance must be installed with sufficient ventilation 
to prevent the occurrence of unacceptable concentrations 
of substances harmful to the health of personnel in the 
room in which it is installed.

n

Warning

Hazard.  Keep  hands  and  tools  clear  from  the  area 
above  the  platens  when  platens  are  in  motion  towards 
the  exhaust  hood.  Be  aware  that  adjacent  platens  may 
unexpectedly  move  at  any  time.  “Turn  Grill  Off”  at 
main  switch  when  cleaning  platens  as  there  can  be  an 
unexpected movement of the platens.

n

Warning

Slipping Hazard: Grease cans must be properly installed 
before  use.  Improper  installation  will  result  in  grease 
on  the  floor  which  will  create  a  slipping  hazard.  Ensure 
grease  cans  are  emptied  and  cleaned  as  needed  to 
prevent grease from overflowing onto the floor. The grill 
may be slippery. Ensure floor area is clean. Care needs to 
be taken as equipment may be hot

n

Warning

Pinch Hazard. Keep hands and tools clear of area between 
platen  and  grill  plate  when  platens  are  in  motion.  Be 
aware that adjacent platens may unexpectedly move at 
any time. “Turn Grill Off” at main switch when cleaning 
platens as there can be an unexpected movement of the 
platens.  

Summary of Contents for Garland ME-1P














Reviews: