background image

LOCATION

n

Warning

Two or more people or a lifting device are required to lift 
this appliance.

n

Warning

To avoid instability the installation area must be capable 
of supporting the combined weight of the equipment and 
product. Additionally the equipment must be level side to 
side and front to back.

n

Warning

No structural material on the appliance should be altered 
or removed to accommodate placement of the appliance 
under a hood.

n

Warning

Be aware of the red mark in the threaded steem caster to 
indicated the maximum adjustment. Adjusting above the 
red mark could cause the caster to fail & the unit to tip. 
For more information see installation section 2.

n

Warning

The  appliance  must  be  isolated  from  the  gas  supply 
piping system by closing its individual manual shutoff 
valve  during  any  pressure  testing  of  the  gas  supply 
piping  system  at  test  pressures  equal  to  or  less  than 
½ psi (3.5 kPa).

,

Caution

This equipment must only be operated under an approved 
hood system in accordance with local regulations in force. 
This unit is intended for indoor use only.

ELECTRICAL

 DANGER

Check all wiring connections, including factory terminals, 
before operation. Connections can become loose during 
shipment and installation.

 DANGER

Do not operate any appliance with a damaged/pinched 
cord or plug. All repairs must be performed by a qualified 
service company.

 DANGER

Failure to disconnect the power at the main power supply 
could result in serious injury or death. The power switch 
DOES NOT disconnect all incoming power.

 DANGER

Copper  wire  suitable  for  at  least  75

°

C  (167°F)  must  be 

used for power connections.

n

Warning

This appliance must be grounded and all field wiring must 
conform to all applicable local and national codes. Refer 
to rating plate for proper voltage. It is the responsibility of 
the end user to provide the disconnect means to satisfy 
the authority having jurisdiction.

n

Warning

Do not use electrical appliances or accessories other than 
those supplied by the manufacturer.

n

Warning

This  equipment  must  be  positioned  so  that  the  plug  is 
accessible unless other means for disconnection from the 
power supply (e.g., circuit breaker or disconnect switch) 
is provided.

n

Warning

Disconnect electric power at the main power disconnect 
for all equipment being serviced. Observe correct polarity 
of  incoming  line  voltage.  Incorrect  polarity  can  lead  to 
erratic operation.

n

Warning

Never touch anything that runs on electricity when your 
hands are wet.

Summary of Contents for Garland ME-1P














Reviews: