Weinzierl 5256 Operation And Installation Manual Download Page 37 | Manualshive

Page: 37 / 49

background image

© 2020 Weinzierl Engineering GmbH

Page 37/49

Behaviour on value higher

This parameter defines the behaviour of the bit in the word register in case the received value
(KNX) is greater than the parameterized value. The following options are available:

▪

No reaction

▪

Register

‘1’

▪

Register

‘0’

Behaviour on value match

This parameter defines the behaviour of the bit in the word register in case the received value
(KNX) corresponds to the parameterized value. The following options are available:

▪

No reaction

▪

Register

‘1’

▪

Register

‘0’

Behaviour on value lower

This parameter defines the behaviour of the bit in the word register in case the received value
(KNX) is smaller than the parameterized value. The following options are available:

▪

No reaction

▪

Register

‘1’

▪

Register

‘0’

5.11.2.2 Direction

– Modbus to KNX

Position (register)

Defines the bit in the word register.

«
...
35
36
37
38
39
...
»

Summary of Contents for 5256


















































Reviews:

No comments

Related manuals for 5256

Brand: SIGNAL FIRE Pages: 33

Brand: FOR-A Pages: 36

Brand: New Rock Technologies Pages: 75

Brand: ZyXEL Communications Pages: 2

Brand: Ericsson Pages: 12

HomePortal 1000

Brand: 2Wire Pages: 44

Brand: 2Wire Pages: 86

Brand: Comcast Pages: 5

Brand: SignalFire Pages: 31

SURFboard SBG7400AC2

Brand: Arris Pages: 22

Brand: Speed Touch Pages: 676

Brand: 2N Pages: 5

Brand: 2N Pages: 33

Brand: 2N Telekomunikace Pages: 5

Unified Security Gateway

Brand: FaceTime Pages: 2

Brand: Avaya Pages: 116

Brand: NetComm Pages: 14

Brand: Salto Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands