Weinzierl 5256 Operation And Installation Manual Download | Manualshive

Page: 41 / 49

background image

© 2020 Weinzierl Engineering GmbH

Page 41/49

Behaviour on value match

This parameter defines the behaviour of the group object (KNX) in the event that the register value
corresponds to the parameterized value. The following options are available:

▪

No reaction

▪

Send value

Value (object)

The value that is sent via the group object (KNX).

Behaviour on value lower

This parameter defines the behaviour of the group object (KNX) in the event that the register value
is smaller than the parameterized value. The following options are available:

▪

No reaction

▪

Send value

Value (object)

The value that is sent via the group object (KNX).

5.12

Channel function “DPT 07 – unsigned – 2 bytes”

Type

The following type is configured:

▪

Word register

2 byte value unsigned (KNX) is written/read to/from area in word register (Modbus)

5.12.1 Type

– Word register

«
...
39
40
41
42
43
...
»

Summary of Contents for 5256


















































Reviews:

No comments

Related manuals for 5256

Brand: CYP Pages: 12

Brand: Rath Pages: 2

Brand: Bticino Pages: 28

Brand: Doepke Pages: 44

NETcon D-G-64NE

Brand: ZIEHL-ABEGG Pages: 27

Brand: TANDBERG Pages: 39

Brand: RTA Pages: 68

Brand: THOMSON Pages: 110

Brand: netvox Pages: 13

Touchstone TG862G

Brand: Arris Pages: 48

Brand: Huawei Pages: 28

Brand: Huawei Pages: 12

Brand: Planet Pages: 2

Dolphin USB 500T

Brand: EnOcean Pages: 11

Brand: FarSite Communications Pages: 2

Brand: Rosonix Technology Pages: 16

Brand: sauter Pages: 26

Brand: RTA Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands