Weinzierl 5256 Operation And Installation Manual Download | Manualshive

Page: 39 / 49

background image

© 2020 Weinzierl Engineering GmbH

Page 39/49

5.11.3.1 Direction

– KNX to Modbus

Value (object)

This parameter defines the value for which the group object (KNX) is checked.

Behaviour on value higher

This parameter defines the behaviour of the word register in case the received value (KNX) is
greater than the parameterized value. The following options are available:

▪

No reaction

▪

Set value in register

Value (register)

The value that is set in the word register.

Behaviour on value match

This parameter defines the behaviour of the word register in case the received value (KNX)
corresponds to the parameterized value. The following options are available:

▪

No reaction

▪

Set value in register

Value (register)

The value that is set in the word register.

«
...
37
38
39
40
41
...
»

Summary of Contents for 5256


















































Reviews:

No comments

Related manuals for 5256

Brand: Gardena Pages: 21

Brand: Xavax Pages: 42

Brand: Cellio Pages: 9

Brand: Sollae Pages: 38

TTN Gateway v1 - EU

Brand: The Things Network Pages: 20

Brand: MikroTik Pages: 9

WIRELESS DATA GATEWAY

Brand: Paradyne Pages: 66

Brand: Planet Pages: 8

Brand: Planet Pages: 16

Brand: Planet Pages: 16

Brand: Planet Pages: 131

Link Gate GSM ISDN

Brand: Linkcom Pages: 22

Brand: Xantrex Pages: 38

Communications gateway

Brand: Xantrex Pages: 70

HomePortal 3801HGV

Brand: 2Wire Pages: 128

Brand: HMM Pages: 41

Brand: Planet Networking & Communication Pages: 2

Brand: Clearswift Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands