Weinzierl 5256 Operation And Installation Manual Download | Manualshive

Page: 31 / 49

background image

© 2020 Weinzierl Engineering GmbH

Page 31/49

Behaviour on value lower

This parameter defines the behaviour of the word register in case the received value (KNX) is
smaller than the parameterized value. The following options are available:

▪

No reaction

▪

Set value in register

Value (register)

The value that is set in the word register.

5.8.3.2 Direction

– Modbus to KNX

Value (register)

This parameter defines the value for which the word register is checked.

Behaviour on value higher

This parameter defines the behaviour of the group object (KNX) in the event that the register value
is greater than the parameterized value. The following options are available:

▪

No reaction

▪

Send value

Value (object)

The value that is sent via the group object (KNX).

«
...
29
30
31
32
33
...
»

Summary of Contents for 5256


















































Reviews:

No comments

Related manuals for 5256

Brand: Salus Pages: 2

Brand: HW Group Pages: 19

EliteConnect SMCWHSG14-G

Brand: SMC Networks Pages: 2

easyconnect ec350

Brand: Netbiter Pages: 40

SMK Access Station Mini

Brand: Sigfox Pages: 17

Brand: Ubee Pages: 6

MultiVOIP MVP130BG

Brand: Bogen Pages: 2

Brand: iSMA CONTROLLI Pages: 29

Brand: Humanscale Pages: 2

Brand: Rotel Pages: 146

Brand: ViewSonic Pages: 34

Brand: BossPac Pages: 27

Brand: ZyXEL Communications Pages: 68

802.11g ADSL 2+ 4-Port Security Gateway HW-D Series

Brand: ZyXEL Communications Pages: 496

Micro-MiniBuffer-256K

Brand: Black Box Pages: 20

Brand: Z-Wave Pages: 17

Brand: Arris Pages: 228

Brand: SICK Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands