manualshive.com logo in svg

SIGNAL FIRE GWDIN, Interface Manual

Share
Download
SIGNAL FIRE GWDIN Interface Manual Download Page 1

 

Rev 1.15

 

SignalFire Telemetry

 

 

1

 

 

 

 

 

 

 

 

 

 

Interface Manual

 

 

Interface Manual

 

DIN Mounted Gateway

 

 

DIN Mounted Gateway

 

SignalFire Part Numbers: GWDIN, GWDIN-ENET 

 

 

SignalFire Part Numbers: GWDIN, GWDIN-ENET 

 

The SignalFire DIN Gateway has the following features:

 

-

 

RS485 connection to Modbus client device

 

-

 

Optional Modbus-TCP Ethernet interface module

 

-

 

Wide range DC power input. 6 to 36VDC

 

-

 

Two open collector digital outputs 

 

-

 

DIN rail mount

 

-

 

Collects and caches Modbus data from all SignalFire remote nodes

 

-

 

Provides configuration and status registers for remote configuration and status monitoring

 

-

 

RP-SMA antenna port for connection to external 900MHz antenna

 

-

 

Stores up to 4700 register values from any combination of remote nodes

 

-

 

Supports transparent Modbus mode

 

-

 

Internal Remote Shut Down (RSD) logic control option

 

-

 

Modbus register re-mapping

 

-

 

Remote configuration of SignalFire devices through an Ethernet gateway connection

 

-

 

Remote sensor configuration (PACTware and RadarMaster) 

 

-

 

Radio is FCC and IC approved

 

-

 

AES 128bit Encryption 

 

-

 

Class 1 Division 2 Area certification pending

 

Summary of Contents for GWDIN


































Reviews:

No comments

Brands by name

Popular brands

Load more brands