manualshive.com logo in svg

SIGNAL FIRE GWDIN, Interface Manual

Share
Download
SIGNAL FIRE GWDIN Interface Manual Download Page 24

 

Rev 1.15

 

SignalFire Telemetry

 

 

24

 

Gateway Event Log

 

Starting  with  Gateway  Firmware  version  7.81  the  Gateway  keeps  an  internal  log  of 
events.  

 

The event log can be viewed from the gateway window of the ToolKit by clicking ‘View 
Gateway Log’ at the bottom of the window. The gateway log events such as reboots, remote nodes 
joining/timing  out,  local  RSD  control  events,  remote  configuration  sessions,  firmware  updates,  and 
more.

 

 

The Node Statistics tab shows information reported every four hours from Sentinels, Scouts, and Flow 
Totalizers to the Gateway with firmware versions from on or after September 21, 2020.

 

 

Saving the Gateway Log

 

Starting with ToolKit version 2.2.21.00, there is a ‘Email Logs To Tech Support’ button in the upper 
right hand corner. It will automatically save all the log entries and statistics, and open a window to 
email SignalFire support with the files attached using your default email client.

 

 

 

 

 

Summary of Contents for GWDIN


































Reviews:

No comments

Brands by name

Popular brands

Load more brands