background image

A

QUA

 L

OGIC

  

COMPANION

 

WATER

 

HEATER

 — 

Product Manual

Pre-installation

 

4HE INCH MIXING VALVE SIDE CLEARANCE
BELOW IS -!.$!4/29

. The 1½” clearance 

on the opposite side is strongly recommended 
(a smaller clearance will make servicing more 
difficult). ADDITIONAL clearance may be 
needed if piping is routed on both sides of 
the boiler/water heater.

&IGURE

Clearance required (in addition to 
clearances specified in the WM97+ 
manual) — right-mounted mixing valve

 vMINTHISSIDE

vMINTHISSIDE

&IGURE

Clearance required (in addition to 
clearances specified in the WM97+ 
manual) — left-mounted mixing valve

 vMINTHISSIDE

vMINTHISSIDE

&IGURE

Align water heater under boiler as needed 
for the piping access panel to fit in place

0IPING

ACCESS

PANEL

Codes

1.  Installation must conform with instructions in this manual and, 

where applicable:

s

local, state, provincial, and national codes, laws, regulations 
and ordinances.

s

in Canada — B149.1 or B149.2 Installation Code.

2.  Aqua Logic (CWH) water heaters are exempt from ASME Section 

VIII, Division 1 Code construction per Interpretation VIII-1-86-
136. Check with local codes for applicability.

3.  Where recommendations in this manual differ from local or na-

tional codes, local or national codes take precedence.

CSA Low Lead Content Only certification

1.  This product has been certified by CSA to Class 6853 01 — Low 

Lead Content Certification Program — Plumbing Products.

2. Applicable 

requirements:

a.  NSF/ANSI 372-2010 Drinking water system components – 

Lead Content.

b.  California Health and Safety Code 116875 (known as AB-

1953-2006).

c.  Louisiana House Bill HB.471, Louisiana’s Lead reduction Law.
d.  Vermont Act No. 193 - 2008 Consumer Products Prohibition 

against Lead.

e.  Maryland House Bill 372 [Statute 12- 605], Business Occupa-

tions and Professionals – Plumbers – Lead Free Materials.

Code restrictions

.ATIONAL3TANDARD0LUMBING#ODE

1.  Single-wall heat exchanger in water heater complies with National 

Standard Plumbing Code, provided that:
a.  Boiler water (including additives) is practically non-toxic, hav-

ing toxicity rating or class of 1, as listed in Clinical Toxicology 
of Commercial Products, and

b.  Boiler water pressure is limited to maximum 30 PSIG by ap-

proved relief valve.

5NIFORM0LUMBING#ODE

1.  Single-wall heat exchangers are permitted if they satisfy all of the 

following requirements —
a.  The heat transfer medium is potable water or contains only 

substances which are recognized as safe by the U. S. Food and 
Drug Administration.

b.  The pressure of the heat transfer medium is maintained less 

than the normal minimum operating pressure of the potable 
water system.

c.  The equipment is permanently labeled to indicate that only 

additives recognized as safe by the FDA shall be used in the 
heat transfer medium.

2.  Other heat exchanger designs may be permitted where approved 

by the Administrative Authority.

Clearances and placement

1.  The Aqua Logic (CWH) must be mounted under the WM97+ 

boiler, with the boiler installed to meet all required clearances in 
the boiler manual.

2. 

). !$$)4)/.

PROVIDE  INCHES CLEARANCE MINIMUM

 on the 

mixing valve side.

3.  Read and comply with “Location,” page 4 of this manual.

Part number 635-500-156/1113

5

Summary of Contents for Aqua Logic













































Reviews: