manualshive.com logo in svg

Weil-McLain Aqua Logic, Product Manual, Page: 22 / 44

Share
Download
Weil-McLain Aqua Logic Product Manual Download Page 22

A

QUA

 L

OGIC

  

COMPANION

 

WATER

 

HEATER

 — 

Product Manual

Aqua Logic (CWH) Performance Mode quick set-up

    

3EEPAGEFORPERFORMANCERATINGSAT()'(0%2&/2-!.#%./2-!,AND%#/./-9

-ODE

$ESCRIPTION

OFF-DISABLED

Contractor-selected — Aqua Logic (CWH) operation is disabled; can only be activated by a contractor
User-selected — Aqua Logic (CWH) operation turned off; can be turned on by user in the Performance Mode 
Menu

  When performance mode is set to OFF-DISABLED, no freeze protection is provided in control 

operation. In other performance modes, the WM97+ control will always maintain a minimum 
temperature to reduce possibility of freeze-up.

HIGH 

PERFORMANCE

Delivers the highest performance available and maximizes the energy of the stored water for demanding 
applications.  Use during peak-demand periods when multiple fixtures will be running.

NORMAL

A balance of performance and efficiency.  Delivers hot water for a shower, sinks, or faucets continually (except 
WM97+70 model).  General setting for most times of the day.

ECONOMY

Saves energy by operating with lower boiler temperatures and storing tank at lower temperature for lowest standby 
losses.  Not recommended for showering with 70°F temperature rise.  Ideal setting in schedule mode for low-use 
periods.

VACATION

Maintains tank temperature above 50°F to deter freezing in tank.  This mode will not supply hot water to the user.

SCHEDULED

This mode allows programming up to 4 different performance modes to occur at different times of the day.  There 
are different schedules for Weekdays (M-F) and Weekends.  This allows energy savings by keeping the tank at low 
temperatures when not needed and meeting peak demands during times of typical high usage.  These times must 
be programmed by the contractor or user.

Part number 635-500-156/1113

22

Summary of Contents for Aqua Logic













































Reviews:

No comments