WEIHONG NK300CX Manual Download Page 52

Page: 52 / 54

上海维宏电子科技股份有限公司

SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD

FAQs (Manufacturer)

Through this section, you can know the following frequently asked questions by

manufacturers during use, and their corresponding causes and solutions for

troubleshooting.

•

Axis servo alarm.

•

Failed to register the system.

•

Drive 400 alarm.

If the solution does not work or you have any other questions, please contact with
our sales engineers.

5.1

Axis Servo Alarm

Cause

Polarity error in port

Axis Servo Alarm

An alarm in axis servo drive.

Solution

Adjust polarity of the corresponding port.

See

Adjust I/O Port Polarity

for details.

Check the servo connecting wire of each axis.

5.2

Failed to Register the System

Cause

You exited

System

interface during registering the system.

Solution

Press

→

to enter into

Sys.

interface, take a picture of the interface, send it

to your developer, and stay at the interface until the end of registration.

Note:

Once you exited

System

interface, you need to take the picture and send it to your developer again.

Summary of Contents for NK300CX























































Search results

Summary of Contents for NK300CX

Reviews:

Related manuals for NK300CX

Brands by name

Popular brands

WEIHONG NK300CX, Manual

Search results

Summary of Contents for NK300CX

Reviews:

Related manuals for NK300CX

Brands by name

Popular brands