Weidmuller IE-SW-VL08M Series User Manual Download Page 72

Page: 72 / 107

IE-SW-VL08M Series User’s Manual

Featured Functions

3-56

IGMP Snooping Enhanced Mode

Setting

Description

Factory Default

Enable

IGMP Multicast packets will forward to :

Learned Multicast Querier Ports

Member Ports

Disable

IGMP Multicast packets will forward to :

Learned multicast Querier Ports

Static Multicast Querier Ports

Querier Connected Ports

Member Ports

Enable

Query Interval

Setting

Description

Factory Default

Numerical value
input by user

Set the query interval of the Querier function globally.
Valid settings are from 20 to 600 seconds.

125 seconds

IGMP Snooping

Setting

Description

Factory Default

Enable/Disable

Select the option to enable the IGMP Snooping
function

per VLAN

Enabled if IGMP
Snooping Enabled
Globally

NOTE

We suggest the following IGMP Snooping configurations:

When the network is mixed with third party switches, such as Cisco:

Select IGMP Snooping Enable:

;

Clear IGMP Snooping Enhanced Mode:

When the network consists entirely of Weidmueller switches:

Select IGMP Snooping Enable-

;

Select IGMP Snooping Enhanced Mode-

;

Querier

Setting

Description

Factory Default

Enable/Disable

Select the option to enable the querier function.

Enabled if IGMP
Snooping is Enabled
Globally

Static Multicast Router Port

Setting

Description

Factory Default

Select/Deselect

Select the option to select which ports will connect to
the multicast routers. It’s active only when IGMP
Snooping is enabled.

Disabled

NOTE

At least one switch must be designated the Querier or enable IGMP snooping and GMRP when
enabling Turbo Ring and IGMP snooping simultaneously.

Summary of Contents for IE-SW-VL08M Series












































































































Search results

Summary of Contents for IE-SW-VL08M Series

Reviews:

Related manuals for IE-SW-VL08M Series

Brands by name

Popular brands

Weidmuller IE-SW-VL08M Series, User Manual

Search results

Summary of Contents for IE-SW-VL08M Series

Reviews:

Related manuals for IE-SW-VL08M Series

Brands by name

Popular brands