Weidmuller IE-SW-VL08M Series User Manual Download Page 66 | Manualshive

Page: 66 / 107

background image

IE-SW-VL08M Series User’s Manual

Featured Functions

3-50

Packets from device H will travel through “Trunk Port 3” with PVID 3. Switch A will recognize
its VLAN and pass it to port 2, but will not remove tags received successfully by device D.

y

Packets from device E will travel through “Trunk Port 3” with tagged VID 4. Switch B will
recognize its VLAN, pass it to port 7, and then remove tags received successfully by device I.
Packets from device I will travel through “Trunk Port 3” with tagged VID 4. Switch A will
recognize its VLAN and pass it to port 2, but will not remove tags received successfully by device
E.

Configuring Virtual LAN

VLAN Settings

To configure the IE-SW-VL08M’s

802.1Q VLAN

, use the VLAN Setting page to configure the

ports.

VLAN Mode

Setting

Description

Factory Default

802.1Q VLAN

Set VLAN mode to 802.1Q VLAN

Port-based VLAN Set VLAN mode to Port-based VLAN

802.1Q VLAN

Management VLAN ID

Setting

Description

Factory Default

VLAN ID ranges
from 1 to 4094

Set the management VLAN of this Ethernet Switch

1

Enable GVRP

Setting

Description

Factory Default

Enable/Disable

Select the option to enable/disable the GVRP function. Enable

Port Type

Setting

Description

Factory Default

Access

This port type is used to connect single devices without
tags.

Trunk

Select “Trunk” port type to connect another 802.1Q
VLAN aware switch or another LAN that combines

Access

«
...
64
65
66
67
68
...
»

Summary of Contents for IE-SW-VL08M Series












































































































Reviews:

No comments

Related manuals for IE-SW-VL08M Series

Brand: QNAP Pages: 20

Ethernet Communication Module DVPEN01-SL

Brand: Delta Electronics Pages: 54

Brand: Delta Electronics Pages: 1

Brand: TRENDnet Pages: 2

IE-SW-VL16-14TX-2SC

Brand: Weidmuller Pages: 17

Brand: IEI Technology Pages: 86

Lite N42B1P Series

Brand: Dahua Technology Pages: 14

RabbitCore RCM4400W

Brand: Rabbit Pages: 126

ControlPoint 2000

Brand: 4Home Pages: 20

SABVISION NVR32

Brand: SAB Pages: 29

Elinx ESW200 Series

Brand: B&B Electronics Pages: 20

Brand: LevelOne Pages: 26

Slideaway CL1008

Brand: ATEN Pages: 77

NetVanta Analog Modem Dial Backup Interface Module

Brand: ADTRAN Pages: 2

24-Port 1000BASE-T

Brand: Comet Labs Pages: 44

Brand: Neousys Technology Pages: 39

Brand: Extron electronics Pages: 19

ENHANCED PSD 239 H2R

Brand: ADTRAN Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands