manualshive.com logo in svg

Weco HeSU 5K3-LV HV, Manual

Share
Download
Weco HeSU 5K3-LV HV Manual Download Page 44

WeCo 5K3-LV-HV

HeSU 5K3-LV HV

Page 44 of 69

V_1.1_21-Nov-2020_LV-HV

SECTION-3 HIGH VOLTAGE CONFIGURATION

3.1 Product Introduction

The 5K3 LV-HV modules can be used as an on-grid or off-grid energy storage system. It is not recommended to use this product for
any purpose other than the intended purpose as described in this document.
Use of this product other than as described in this document will nullify the product guarantee. The substitution or installation of any
components of this battery will nullify the product guarantee.
The use of any components contained within or connected to this battery other than the products sold as part of this product or
recommended by the manufacturer will nullify the product guarantee.

ATTENTION:

do not exceed the number of 6 modules each tower

ATTENTION:

The maximum number of batteries that can be connected in series is 12

ATTENTION:

The HV BOX is a compulsory protection and communication device that must be installed for any High Voltage Configuration

ATTENTION:

Attempting to operate the batteries with less than four batteries in series or more than 12 batteries in series will nullify the

product guarantee.

Module Weight 52Kg

ATTENTION

A cluster of 12 modules weight 624Kg, the support structure/floor must be properly inspected before start the installation of the
modules.

Summary of Contents for HeSU 5K3-LV HV






































































Reviews:

No comments

Brands by name

Popular brands

Load more brands