background image

3

www.waynepumps.com

POOL 
COVER

APPLICATION AND OPERATION (CON'T)  

1.   This pump has been designed with 1-1/4 in. NPT 

discharge connection size. Attach pipe or fitting to the 
discharge or use the supplied garden hose adapter/
check valve. Thread the female end of the garden hose to 
the male end of the garden hose adapter/check valve. 

2.   Use a hose washer (not included) on the garden hose for 

correct pump operation.

3.   For best pump performance, unwind the hose before 

starting the pump. This will help remove any kinks or 
binds in the hose and allow the unit to pump with less 
restriction.

  a. DO NOT place the pump on a weak, damaged, or leaking 

pool cover. Placing the pump on a damaged pool cover 
could cause the cover to give way, or could allow the 
pump to remove treated swimming water from the pool 
in addition to rainwater.

  b. Install the “snap-on” debris strainer.  Begin by lining up 

the pump base profile with the profile of the strainer base 
using the switch housing as a guide. Tilt the pump back 
and guide the rear of the pump (opposite the discharge) 
into the strainer base. Once the rear of the pump is 
in place, gently rotate the pump down until the latch 
engages.

  c. To remove debris strainer release latch and guide pump 

out of strainer in the reverse motion of installation.

4.   With pump unplugged set the pump on the pool cover, 

where water will collect. Do NOT set the pump directly 
on mud, sand surfaces or in leaves. For best results 
make sure the pump strainer is making full contact with 
a clean area of the pool cover. This will allow the strainer 
to properly filter debris and help prevent clogging 

PULL ACROSS PUMP INSTALLATION

    To aid in pump placement on pool cover, secure provided 

25 ft. rope

 

to the pull to shore loop (Figure B).

Figure A - In-ground pool installation (cut-away view)

A2

A3

13' MAXIMUM 
PUMPING HEIGHT

AVOID PINCHING OR 

DAMAGING POWER CORD 

AND HOSE ON POOL EDGE

A1

    A1. Connect discharge hose to pump check valve and place hose 

end away from pool, where water will be displaced.

    A2. Attach provided 25 ft. rope to handle of pump, and lower pump 

onto pool cover where water will collect.

    A3. Do NOT exceed the 13 ft. maximum pumping height for this 

pump or switch may not function properly. Plug in pump to allow for 

automatic operation.

     For REMOVAL unplug pump and retrieve using 

rope.

Figure B - Pull to shore loop 

FEED ROPE 

THROUGH LOOP AND 

SECURE WITH KNOT 

    D1. Holding the provided 25 ft. rope, walk around pool until you are 

even with the pump on the opposite side.  

D2. Pull the 25 ft. rope towards you until the pump is in the center 

of the pool cover where water will collect. Secure rope for easy 

removal (see Figure E) when weather permits. Plug in pump to allow 

for automatic operation.

Figure C - Pull Across installation (side view)

C1

25 FT. ROPE 

AVOID PINCHING 

OR DAMAGING 

POWER CORD 

AND HOSE ON 

POOL EDGE

    C1. Connect provided 25 ft. rope to pull to shore loop (see Figure B) 

and discharge hose to the pump.

    C2. Place pump on pool cover near edge of pool (see Figure C). If 

floatation device is used under the pool cover, place pump at the 

lowest point on the pool cover where water will collect.

Figure D - Pull Across Installation (top view) 

D2

D1

25 FT. (INCLUDED)  

ROPE 

DROP-IN PUMP APPLICATION

 

 

 Always use debris strainer when placing pump        

  

on a pool cover. The strainer helps protect the pool cover 

from damage, filters debris, and increases pump stability.

WAPC250

Summary of Contents for WAPC250





















Reviews: