background image

This Installation document is available at no charge from:
- Your local Wayne Dalton Sales Center, or
- Online at 

www.Wayne-Dalton.com

, or

- By mailing to: Wayne Dalton, a division of Overhead Door Corporation, P.O. Box 

67, Mt. Hope, OH., 44660

©Copyright 2017

REV13_06/02/2017

Part Number

T a b l e   O f   C o n t e n t s

344597

PLEASE DO NOT RETURN THIS PRODUCT 

TO THE STORE

If you need assistance, please call 1-866-
569-3799 (press Option 1) and follow the 
prompts to contact a customer service 
representative. They will be happy to handle 
any questions that you may have.

Pre-Installation 2

Important Safety Instructions 

2

Removing an Existing Door and Preparing the Opening 

2

Package Contents 

3

Door Section Identification 

4

Tools Required 

4

Breakdown Of Parts 

5

Door Installation Instructions 

6

Counterbalance Installation Instructions 

13

Optional Installation 

16

Trolley Arm Hookup 

16

Inside Lock 

16

Pull Down Rope 

16

Maintenance 17

Cleaning Your Garage Door 

17

Painting Your Garage Door 

17

Maintaining The Finish On Your Garage Door 

17

Operation And Maintenance 

17

Warranty 19

Wayne Dalton, a division of Overhead Door Corporation

Models 8300 / 8500

E

x t E n s i o n

i

nstallation

 i

nstructions

 a

nd

 o

wnEr

s

 

M

anual

r

EsidEntial

 

 

s

tandard

 l

ift

To avoid possible injury, read and fully understand the enclosed 
instructions carefully before installing and operating the garage door. Pay 
close attention to all warnings and notes. After installation is complete, 
fasten this manual near garage door for easy reference.

IMPORTANT NOTICES!

Summary of Contents for 8500





















Reviews: