background image

2

•  Most field problems occur because dirt and debris are present 

in the system at the time of installation and becomes trapped 

in check No. 1. The system should be flushed before the back-

flow valve is installed. If the system is not flushed until after the 

backflow valve is installed, remove both check modules from 

the valve and open the inlet shutoff to allow water to flow for 

a sufficient time to flush debris from the water line. If debris in 

the water system continues to cause fouling, a strainer can be 

installed upstream of the backflow assembly.

•  Series 957, 957RPDA, and LF957RPDA can be installed in 

either horizontal, “N” pattern, or “Z” pattern position as long 

as the backflow assembly is installed in accordance with the 

direction of the flow arrow on the assembly and the local water 

authority approves the installation. 

•  The assembly should be installed with adequate clearance 

around the valve to allow for inspection, testing, and servicing. 

Ensure a minimum clearance of 12" between the lower  

portion of the assembly and the floor or grade. The valve 

should be protected from freezing.

•  Installing a backflow preventer in a pit or vault is not  

recommended.

•  Normal discharge and nuisance spitting are accommodated 

by the use of a Watts air gap fitting and a fabricated indirect 

waste line. A floor drain appropriately sized for the discharge 

must be provided in case of excessive discharge. For more 

information, download ES-RVD for relief valve discharge rates.

•  When installing an air gap, attach the air gap brackets directly 

onto the flood sensor.

•  Have a certified technician test the series at the time  

of installation.

 

NOTICE

Assembly body should not be painted.

Relief Valve Discharge Rates 2

1

2

" – 10" 

  lpm gpm

 1330 350

 1140 300

  950 250

  760 200

  570 150

  380 100

 190 50

  0 0

20 

40 

60 

80 psi

138 

276 

413 

551 kPa

Rate of Flow

Pressure

Horizontal Installation

N Pattern

Z Pattern

Installation Guidelines

Summary of Contents for 957 Series

























Reviews: