background image

 

 

 

  CommLink IV Technical Guide              

19

Operator Interface 

Troubleshooting the USB Drivers for Windows

®

 Vista

5. The

 USB Serial Port Properties Window

 will appear. 

This window will have information pertaining to the 
device listed in the Device Status area of the window. 

Click

 on the 

<Driver>

 tab at the top.

6.  In the Driver tab, 

select 

<Update Driver>

.

7. The 

Update Driver Software Window

 will appear. 

Click

 the option 

<Browse my computer for

driver software>

.

8.  The screen will now display the message, “Search for 

driver software in this location:” If the location is
correct, 

click

 

<Next> 

and go to step 10. If not, 

click 

<Browse>

.

9. 

Select 

the CD-ROM location from the list of folders 

and then 

click 

<OK>

.

10.  A message will appear that states, “Installing driver 

software...” 

11.  When the installation is complete, the window below 

will appear. 

Click

 

<Close>

.

12.  If the problem was in the Universal Bus drivers - 

USB Serial Converter, then the 

Found New Hardware 

Screen

 for the USB serial port will appear. You will 

have to go through the screens to install that driver.

13.  If the USB serial port driver was the only driver

updated, you will see this screen:

Summary of Contents for CommLink IV

























Reviews: