WattMaster CommLink IV Technical Manual Download Page 16

Page: 16 / 24

CommLink IV Technical Guide

Operator Interface

CommLink IV LED Descriptions

Figure 3: CommLink IV LED Display

STATUS

RX-USB

TX-USB

LOOP

TX-CPU

RX-CPU

ACT

-LAN

LNK-LAN

CommLink IV

www.wattmaster.com

CommLink IV LED Descriptions

LOOP -

Indicates communication activity on local controller

network. This LED ﬂ ickers when data is exchanged
with the controller network.

TX-USB

- Indicates transmitted data status of USB

connection. This LED only ﬂ ashes when your
CommLink is connected to a computer and data is sent
to Prism from the CommLink via USB.

RX-USB

- Indicates received data status of USB connection.

This LED only ﬂ ashes when your CommLink is connected
to a computer and data is sent from Prism to the CommLink
via USB.

TX-CPU -

Indicates transmitted data status. This LED only

ﬂ ashes when your CommLink is connected to a computer
and data is sent to Prism from the CommLink using USB or
Ethernet.

RX-CPU -

Indicates received data status. This LED only

ﬂ ashes when your CommLink is connected to a computer
and data is sent from Prism to the CommLink using USB or
Ethernet.

ACT-LAN

- Indicates activity on the local area network. This

LED ﬂ ashes on when LAN is transmitting and receiving
data and is only operational when the IP Module Kit is
installed.

LNK-LAN

- Indicates local area network is connected. This

LED is on when connected to LAN and is only operational
when the IP Module Kit is installed.

Summary of Contents for CommLink IV

























Search results

Summary of Contents for CommLink IV

Reviews:

Related manuals for CommLink IV

Brands by name

Popular brands

WattMaster CommLink IV, Technical Manual

Search results

Summary of Contents for CommLink IV

Reviews:

Related manuals for CommLink IV

Brands by name

Popular brands