background image

 

 

RS1  

      

Master Programming Mode

Master Programming Mode

To enter Master Programming Mode, press and hold both buttons for 5 seconds.

Note:  All Master Programming functions have been preset at the factory. Unless a change is desired,  it is 

NOT

 

 

necessary to enter Master Programming Mode.

1. Regeneration Time ( r )

 

 

 

Example  [  

r 2A

  ]

 

- The time of day at which regeneration may take place is designated by the letter “

r

”.

 

- Default regeneration time setting for 

SOFTENERS is 2a

 

- The first display digit indicates A.M. or P.M. To change the value, press the 

Set/Change

 button.

 

- Press 

Menu/Enter

 button to accept the value and move to the next digit.

 

- The second and third display digits indicate the hour at which the regeneration will occur.

 

- Change the digits with the 

Set/Change

 button and accept with the 

Menu/Enter

 button.

 

- After the entire display flashes, press the 

Menu/Enter

 button to move to the next menu item.

2. 

Regeneration Day Override (A)

 

 

- Press 

Menu/Enter

 button. This display is used to set the maximum amount of time (in days)  

 

              

 

  the unit can be in service without regeneration. This setting is identified by the

  

  letter “A” in the left digit. Regeneration will begin at the scheduled time. A setting of zero 

 

  will cancel this feature. 

 

- Example: Override every 7 days (

A-07

), default setting, or cancel setting (

A-00

). Maximum is 29.

3. 

Regeneration Cycle Step Times (Steps 1, 2, 3, 4)

    

    

Example [ 

3 - 10

 ]

 

- The next 4 displays set the duration of time in minutes for each regeneration cycle step.

 

- The step number which is currently modifiable is indicated on the far left of the display screen.

 

- The number of minutes allotted for the selected backwash step is displayed on the far right.

 

- Change the digit values using the 

Set/Change 

and 

Menu/Enter

 buttons as described above.

  

4. 

System Capacity in Grains 

( c ) 

 

- Press the 

Menu/Enter

 button. This display is used to set the system capacity in grains    

 

              

 

  and is used in conjunction with the hardness setting to calculate total gallons of treated water 

 

  available between regenerations. This option is identified by the letter “c” in the left digit. 

 

  The maximum value for this item is 399. Example: 32,000 grain capacity ( c 032 ).

12

Summary of Contents for rs1

























Reviews: