background image

17

 

 

                                                                                                                                                   

                                                                                                                                         

 

 

                                                                                                                                                   

                                                                                                                                         

1

4

2

3

7

5

6

REF

DESCRIPTION

PART NO. 

1

D15 Bypass                                 (included with all units)

20017X283

2

1” NPT Elbow Set                        (included with all units)

20017X284

3

1” Female Straight Slip Set                         (optional)

20017X288

4

1” NPT Straight Set                                      (optional)

20017X289

5

3/4” NPT Straight Set                                  (optional)

20017X307

6

1” X 

3/4”

  Brass Sweat Connector Set        (optional)

20017X304

7a

Elbow, Vertical Adapter

 Blank                           

(optional)

20017X295

7b

Elbow, Vertical Adapter

 1/4” NPT Tapped       

(optional)

20017X294

Bypass Assembly 

Summary of Contents for Provectr Plus AF10AC-3

























Reviews: