Watec WAT-2200Mk-2 User Manual Download Page 47 | Manualshive

Page: 47 / 61

background image

47

3.6.6.

CVBS FORMAT

Set the CVBS output format. Default: NTSC1

NTSC1
PAL1

Output NTSC/PAL format after compressing horizontally the 1920 x 1080 pixel (aspect

ratio 16:9) imaged with an image sensor to aspect ratio 4:3.

The both ends of the viewing angle can be seen even though the image is distorted due to

the horizontal compression.

NTSC2
PAL2

Output NTSC/PAL format after cutting-out excluding the both ends 240 pixel of the 1920 x

1080 pixel imaged with an image sensor to 1440 x 1080 pixel (aspect ratio 4:3).

The image does not be distorted but the ends of the viewing angle will not be displayed.

(The 1920 x 1080 pixel before cut-out will be displayed for the SDI.)

(SDI-out, 1920x1080)

NTSC1 NTSC2

PAL1 PAL2

Figure 29. CVBS FORMAT

«
...
45
46
47
48
49
...
»

Summary of Contents for WAT-2200Mk-2






























































Reviews:

No comments

Related manuals for WAT-2200Mk-2

Brand: Acer Pages: 18

Brand: Canon Pages: 6

DIGITAL IXUS 430

Brand: Canon Pages: 2

Brand: Canon Pages: 28

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 15

DMC-TZ3A - Lumix Digital Camera

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 64

Brand: Panasonic Pages: 31

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 225

DMC-FX30A - Lumix Digital Camera

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 24

Brand: Samsung Pages: 44

Brand: Z3 Technology Pages: 5

Brand: Olympus Pages: 148

Brand: Canon Pages: 164

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands