background image

SERVICE PARTS

 

All kits include applicable hardware and step-by-step instructions. 

KIT NAME

 

ORDER NO

 

DESCRIPTION 

 

Rubber Feet

 

2102273

 

Set of (4) replacement feet for legs.

 

Casters

 

2102275

 

Set of (4) replacement casters .

 

Short Caster Actuator

 

2102277

 

One short caster actuator for right rear or left front casters.

 

Long Caster Actuator

 

2102279

 

One long caster actuator for left rear or right front casters.

 

Lift Actuator

 

2102281

 

Set of (2) lift actuators.

 

Power Cord

 

2102283

 

Replacement power cord that plugs into wall receptacle.

 

Power Cord Hooks

 

2102285

 

Set of (2) Hooks on right side of LiftMate that secure the power cord.

 

E-Stop Interface 
Button

 

2102287

 

Red Button that attaches to the outside shroud. The emergency stop switch is inside the 
unit and is connected to the other side of this button. Kit includes (1) button.

 

E-Stop Switch

 

2102289

 

The switch that is mated to the E-Stop button. The kit includes (1) switch. The switch 
disconnects power to the lift actuators only.

 

Hand Pendant

 

2102291

 

Replacement hand pendant with strain relief and button graphics label attached.

 

Hand Pendant Hook

 

2102293

 

Hook for hanging hand pendant when not in use.

 

Back Cover

 

2102295

 

Sliding two piece cover that spans the gap between the platform and base.

 

Platform Mat

 

2102297

 

Slip resistant mat that covers the top of the platform.

 

Platform Bumper

 

2102299

 

Yellow rubber strip covering the front edge of the platform.

 

Right Outer Shroud

 

2102301

 

Right outside cover with power cord hooks and E-Stop button attached.

 

Left Outer Shroud

 

2102303

 

Left outside cover with E-Stop button attached.

 

Right Inner Shroud

 

2102305

 

Right inside cover.

 

Left Inner Shroud

 

2102307

 

Left inside cover.

 

Battery

 

2102309

 

Replaceable storage battery specifically designed for this unit.

 

Control Box

 

2102311

 

Control unit through which the power cord is connected and the battery is charged. The 
hand pendant input and the lift and caster actuator outputs are connected as well. Lift 
actuator synchronization and battery management is monitored through the control box.

 

E-Stop Wiring Harness

 

2102313

 

The wiring harness that connects to the E-Stop switches and allows power to operate the 
lift actuators when switches are in their normal state.

 

L Caster Actuator 
Harness

 

2102315

 

The wiring harness that brings power to the left caster actuators.

 

R Caster Actuator 
Harness

 

2102317

 

The wiring harness that brings power to the right caster actuators.

 

L Lift Actuator 
Harness

 

2102319

 

The wiring harness that brings power to the left lift actuator.

 

R Lift Actuator 
Harness

 

2102321

 

The wiring harness that brings power to the right lift actuator.

 

Battery Wiring 
Harness

 

2102323

 

The wiring harness that goes from the control box to a receptacle that the 
battery plugs into. Charge current to the battery and power from the battery 
travel through this harness.

 

Summary of Contents for Brewer Patient LiftMate
















Reviews: