manualshive.com logo in svg

Wallenstein WP245, Operator'S Manual

Share
Download
Wallenstein WP245 Operator'S Manual Download Page 42

7.4  Power Pack Option–Maintenance

 NOTE:

This procedure is for the Optional Power Pack. 
Please refer to your tractor's maintenance 
guide concerning hydraulic oil and filter service 
instructions. 

 CAUTION!

Risk of burns to exposed skin. 

Hydraulic oil becomes hot during 

operation. Hoses, lines, and other 

parts become hot as well. Wait for 

the oil and components to cool 

before starting any maintenance or 

inspection work.

W028

7.4.1  Drain and replace oil

Change hydraulic oil every 100 hours or annually. 

Make sure tractor engine is off and all controls are in neutral.

Allow the machine to cool before changing the oil. Hot oil can 
cause burns if it contacts exposed skin. It is best to change 
oil while the machine is warm to keep the contaminants in 
suspension.

1. 

Place a pan of suitable capacity under the hydraulic oil 
reservoir drain. Reservoir holds 7.1 US gal (27 L).

2. 

Remove the drain plug to drain the oil.

01302

Fig.  49 – 

Oil reservoir drain plug

3. 

Replace the drain plug and fill the reservoir with Dexron® III 
ATF for all operating conditions. Dexron VI or Mercon

® 

are 

acceptable substitutes. 

4. 

Operate the machine for 1–2 minutes while operating 
cylinder. Recheck oil level. Oil level should be approximately 
1" (25 mm) from the top of the tank. 

5. 

Check for leaks at the drain.

Dispose of the old or any spilled oil in an approved manner.

7.4.2  Remove and clean the filter

R

emove and clean oil filter every 100 hours or annually. 

The 

filter is washable.

 NOTE:

The tank does not have to be drained to clean the 
filter.

1. 

Remove the 3 screws from the oil filter cover on the top of 
the reservoir.

2. 

Remove the filter cover and pull out the hydraulic oil filter.

3. 

Wash the filter screen with mineral spirits (Varsol™). 
Inspect the filter mesh for any holes, perforation, rust, or 
tears.

4. 

Place the filter screen into the tank and secure the filter 
cover.

 

01301

1

2

3

Fig.  50 – 

Reservoir filler cap and filter

1.  Filler Cap
2.  Filter Cover
3.  Filter

Service and Maintenance

WP245 / WP275

3-Point Hitch Firewood Processor

42

Summary of Contents for WP245





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands