manualshive.com logo in svg

Wallenstein WP245, Operator'S Manual

Share
Download
Wallenstein WP245 Operator'S Manual Download Page 15

IMPORTANT!  If parts are replaced that have safety signs on 
them, new signs must be applied. Safety signs must always 
be replaced if they become damaged, are removed, or 
become illegible.

Safety signs are included in the product decal kit available from 
your authorized dealer. Decals are not available separately.

2.9.1  Replacing Damaged Safety Signs

• 

Always keep safety signs clean and legible.

• 

Replace safety signs that are missing or have become 
illegible.

• 

Parts that were replaced with a safety decal on them must 
also have the safety sign replaced.

• 

Replacement safety signs are available from your 
authorized Distributor, Dealer Parts Department, or 
Wallenstein Equipment.

Procedure

1. 

Be sure that the installation area is clean and dry.

2. 

Be sure temperature is above 50 °F (10 °C).

3. 

Determine exact position before removing from the backing 
paper.

4. 

Pull the decal off the backing sheet, align the sign over 
the specified area, then carefully press the exposed sticky 
backing in place.

5. 

Use a piece of the backing paper to smooth the decal out, 
pressing from the center outwards.

6. 

Small air pockets can be pierced with a pin and smoothed 
out using the piece of sign backing paper.

 Safety

WP245 / WP275
3-Point Hitch Firewood Processor

Safety

15

Summary of Contents for WP245





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands