manualshive.com logo in svg

Wallenstein WP245, Operator'S Manual

Share
Download
Wallenstein WP245 Operator'S Manual Download Page 22

5.  Attaching / Unhooking

The Wood Processor should always be parked on a level, dry 
area that is free of debris and other foreign objects. When 
attaching the machine to a tractor, follow this procedure:

1. 

Clear the area of bystanders. Make sure there is enough 
room and clearance to safely back up to the machine.

2. 

Back up slowly and align the lower link arms to the 
mounting brackets on the machine.

3. 

Be sure the drawbar dimension is at the short length for 
the tractor being used. Refer to the tractor manual for 
adjustment procedures, or the drawbar can be removed.

4. 

Stop tractor, set park brake.

IMPORTANT!  It may be necessary to add weight to the 
lower lift arms to bring them to the required height.

5.1  Mounting

1. 

Remove the lock pins from the side arms to allow the lower 
lift arms to be in their fully 'sway' configuration.

2. 

Align the lower link with the left-hand mounting bracket.

3. 

Insert the left-hand pin through the ball and install the 
retainer.

4. 

Align the right-hand arm to the pin by turning the jackscrew 
on the arm.

5. 

Insert the right-hand pin through the ball and install the 
retainer. Return the jackscrew to its starting position.

Fig.  12 – 

Aligning

Fig.  13 – 

Sway anchor pin (typical)

Fig.  15 – 

Pinned – right side

Fig.  14 – 

Aligned – left side

Attaching / Unhooking

WP245 / WP275

3-Point Hitch Firewood Processor

22

Summary of Contents for WP245





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands