WAGO TEchDocs 765-4501/0100-0000 Manual Download Page 26

Page: 26 / 136

765-4501/0100-0000

Properties

Product manual | Version: 1.1.0
8PORT IOL-A FLD EI DC 24V 2.0A

4.6 Regulations and Standards

The following regulations and standards were used in the development of the module:

Table 18: Standards and Regulations

Standard

Title

EN 61000-6-2

Electromagnetic compatibility (EMC) – Immunity for industrial en-
vironments

EN 61000-6-4

Electromagnetic compatibility (EMC) – Emission standard for in-
dustrial environments

IEC 61158

EtherNet/IP

4.7 Approvals

The following approvals have been granted for the product:

Conformity marking

UL 61010-1 and UL 61010-2-201, “Ordinary
Location”

Pending

Bluetooth

This module has an RF transmitter with the following specifica-
tions:
•

Operating frequency: 2402–2480 MHz

•

Maximum RF output power: < 20 mW

RED

Certificate number: R20-0935-01-TEC (Wideline)

FCC

FCC ID: 2AKUE-WIDELINE

ISED

Certificate number: 22322-WIDELINE

Note

More information on approvals

You can find detailed information on the approvals online at:

www.wago.com

/<item

number>

Summary of Contents for TEchDocs 765-4501/0100-0000









































































































































Search results

Summary of Contents for TEchDocs 765-4501/0100-0000

Reviews:

Related manuals for TEchDocs 765-4501/0100-0000

Brands by name

Popular brands

WAGO TEchDocs 765-4501/0100-0000, Manual

Search results

Summary of Contents for TEchDocs 765-4501/0100-0000

Reviews:

Related manuals for TEchDocs 765-4501/0100-0000

Brands by name

Popular brands