WAGO TEchDocs 765-4501/0100-0000 Manual Download Page 130 | Manualshive

Page: 130 / 136

background image

765-4501/0100-0000

Appendix

130

Product manual | Version: 1.1.0
8PORT IOL-A FLD EI DC 24V 2.0A

We declare that we meet the EN 62479 standard with respect to the limiting value for low
powers less than 20 mW. Therefore, the product fundamentally corresponds to the Euro-
pean limiting values for high-frequency radiation.

Product Designs

SlimLine (W × H × D)

35 × 30 × 210 mm

WideLine (W × H × D)

60 × 30 × 210 mm

Temperature range

Table 98: Temperature range

Surrounding air temperature (operation)

–25 °C ... +70 °C

Surrounding air temperature (storage)

–40 °C ... +80 °C

Maximum temperature change

3 K / min

Voltage range

Table 99: Voltage range

Voltage source

24 V DC PELV (Protective Extra Low Voltage) or
SELV (Safety Extra Low Voltage)

Voltage 1L

Voltage 2L

24 V DC, –25 %/+30 % (18 V DC ... 31.2 V DC)

Digital output

Output voltage 24 V DC, 1L powered

Power supply actuator/sensor

Output voltage 24 V DC, 1L powered and 2L powered

Overvoltage category

II (EN 60664-1)

14.3 Protected Rights

• Adobe

®

and Acrobat

®

are registered trademarks of Adobe Systems Inc.

• Android

TM

is a trademark of Google LLC.

• Apple, the Apple logo, iPhone, iPad and iPod touch are registered trademarks of Apple

Inc. registered in the USA and other countries. “App Store” is a service mark of Apple
Inc.

• AS-Interface

®

is a registered trademark of the AS-International Association e.V.

• BACnet

®

is a registered trademark of the American Society of Heating, Refrigerating

and Air Conditioning Engineers, Inc. (ASHRAE).

•

Bluetooth

®

is a registered trademark of Bluetooth SIG, Inc.

• CiA

®

and CANopen

®

are registered trademarks of CAN in AUTOMATION – Interna-

tional Users and Manufacturers Group e.V.

• DALI is a registered trademark of the Digital Illumination Interface Alliance (DiiA).
• EtherCAT

®

is a registered trademark and patented technology licensed by Beckhoff

Automation GmbH, Germany.

• ETHERNET/IP™ is a registered trademark of the Open DeviceNet Vendor Association,

Inc (ODVA).

• EnOcean

®

is a registered trademark of EnOcean GmbH.

• Google Play

TM

is a registered trademark of Google Inc.

• IO-Link is a registered trademark of PROFIBUS Nutzerorganisation e.V.
• KNX

®

is a registered trademark of the KNX Association cvba.

• Linux

®

is a registered trademark of Linus Torvalds.

• LON

®

is a registered trademark of the Echelon Corporation.

«
...
128
129
130
131
132
...
»

Summary of Contents for TEchDocs 765-4501/0100-0000









































































































































Reviews:

No comments

Related manuals for TEchDocs 765-4501/0100-0000

Brand: Sven Pages: 12

PROX-BOOSTER 2G

Brand: Nedap Pages: 25

Brand: Equalizer Pages: 26

Brand: HK Audio Pages: 20

Brand: Viking Pages: 4

Brand: Rain Bird Pages: 2

Brand: Valx Pages: 28

Brand: Magnavox Pages: 23

Brand: GE Pages: 2

DH-VTH111 Series

Brand: Dahua Pages: 12

Brand: TCS Pages: 2

Brand: Vimar Pages: 8

Brand: TrailKeg Pages: 4

UltraTwin FreeSpan

Brand: Liko Pages: 10

Brand: Ravaglioli Pages: 60

Brand: Skov Pages: 28

Brand: Wavemaster Pages: 32

ioLogik E1500 Series

Brand: Moxa Technologies Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands