manualshive.com logo in svg

Wachs FF 424, User Manual, Page: 62 / 70

Share
Download
Wachs FF 424 User Manual Download Page 62

SDB 412 and FF 424

62

Part No. 66-MAN-01, Rev. A

E.H. Wachs

Leg Extension Adapter (66-415-00)

6

7

8

1

9

2

"A"

DIMENSIONS IN BRACKETS ARE MILLIMETERS

ITEM

PART NUMBER

 QTY. 

DESCRIPTION

1

66-092-00

1

ADAPTER, 12.8" - 20" MANDREL

2

66-096-00

1

SCREW, 1" DIA. ADJUSTABLE

3

66-101-00

2

BLOCK, LEG STORAGE (NOT SHOWN)

4

66-102-00

1

LABEL, LEG RANGE (NOT SHOWN)

5

66-102-01

1

LABEL, LEG RANGE (NOT SHOWN)

6

90-069-05

3

PLUNGER, 5/16-18 X 1/2 BALL

7

90-090-52

3

SHCS, 1/2-20 X 2-1/4

8

WHERE USED

A/R

LEG, 1" DIA.

9

WHERE USED

A/R

LEG, 1" DIA. ADJUSTABLE

18.49 [469.6]

19.29 [489.9]

19.21 [487.9]

20.01 [508.2]

66-093-15

66-093-16

66-094-15

66-094-16

-WHERE USED-

66-093-09

ITEM

66-093-11

66-093-12

QTY.

82

PART NO.

66-093-10

66-094-13

66-094-12

66-094-11

66-094-10

66-094-09

LEG, 1"

DESCRIPTION

ITEM

9

PART NO.

1

QTY.

DESCRIPTION

LEG, 1" ADJUSTABLE

DIMENSION "A" DIA.

17.13 [435.0]

15.69 [398.5]

MAX.

14.97 [380.2]

17.85 [453.3]

16.41 [416.8]

MIN.

17.05 [433.0]

16.33 [414.8]

15.61 [396.5]

14.89 [378.2]

14.17 [359.9]

66-093-13

66-093-14

17.77 [451.3]

18.57 [471.6]

66-094-14

66-093-07

66-093-08

66-094-07

66-094-08

12.73 [323.3]

13.53 [343.6]

13.45 [341.6]

14.25 [361.9]

Summary of Contents for FF 424







































































Reviews:

No comments