39
EN
M1.2.CUT80HFI.NLFREN 09102018
4�2 Operating method
1. Turn on the power switch of the machine, and the power indicator illuminates.
2. Select proper working mode and proper function. There are two working modes available on the machine panel: 2T
and 4T. There are two functions available: normal cutting and metal mesh cutting. The electrode and nozzle are more
easily to wear out in metal mesh cutting.
3. Push the torch trigger on the cutting torch, the cutting machine works.
4. Set cutting current according to the thickness of workpiece.
5. Bring the copper nozzle of the cutting torch into contact with the workpiece (For models with pilot arc function, keep
a distance of about 2 mm between the copper nozzle of the torch and the workpiece), and then push the torch
trigger. After the arc is ignited and started, raise the cutting torch to the position about 1 mm above the workpiece,
and start cutting.
4�3 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it will shorten the lifespan of
the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece, unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters fly from the top of
workpiece, it indicates that the workpiece can not be fully cut because the cutting torch is moved
too fast or the cutting current is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance between the nozzle and
workpiece. If the torch is pressed against the workpiece, the nozzle may stick to the workpiece, and
smooth cutting is unavailable.
For cutting round workpiece or to meet precise cutting requirement, molding board or other
assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check if the arc is moving with the
cutting line. If the space is not enough, don’t bend the cable too much, step on or press upon the
cable to avoid suffocating of gas flow. The cutting torch may be burned because the gas flow is too
small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling effect of the nozzle. Clean
up the dust and spatters on the torch head after using everyday to ensure good cooling effect.
The workpiece is not cut fully� This may be caused by:
• The cutting current is too low.
• The cutting speed is too high.
• The electrode and nozzle of the torch are burned.
• The workpiece is too thick.
Molten slag drops from the bottom of workpiece� This may be caused by:
• The cutting speed is too low.
• The electrode and nozzle of the torch are burned.
• The cutting current is too high.
11
3. OPERA
TION
3.3 Operation method
1
)
Turn on the power switch of the machine, and the power indicator illuminates.
2
)
Select proper working mode and proper function. There are two working modes available on
the machine panel: 2T and 4T. There are two functions available: normal cutting and metal mesh
cutting. The electrode and nozzle are more easily to wear out in metal mesh cutting.
3
)
Push the torch trigger on the cutting torch, the cutting machine works.
4
)
Set cutting current according to the thickness of workpiece.
5
)
Bring the copper nozzle of the cutting torch into contact with the workpiece
(
For models with
pilot arc function, keep a distance of about 2mm between the copper nozzle of the torch and the
workpiece.
)
, and then push the torch trigger. After the arc is ignited and started, raise the cutting
torch to the position about 1mm above the workpiece, and start cutting.
3.4 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it
will shorten the lifespan of the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece,
unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters
fly from the top of workpiece, it indicates that the workpiece can not be
fully cut because the cutting torch is moved too fast or the cutting current
is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance
between the nozzle and workpiece. If the torch is pressed against the
workpiece, the nozzle may stick to the workpiece, and smooth cutting
is unavailable.
For cutting round workpiece or to meet precise cutting requirement,
molding board or other assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check
if the arc is moving with the cutting line. If the space is not enough,
don’t bend the cable too much, step on or press upon the cable to avoid
suffocating of gas flow. The cutting torch may be burned because the
gas flow is too small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling
effect of the nozzle. Clean up the dust and spatters on the torch head
after using everyday to ensure good cooling effect.
11
3. OPERA
TION
3.3 Operation method
1
)
Turn on the power switch of the machine, and the power indicator illuminates.
2
)
Select proper working mode and proper function. There are two working modes available on
the machine panel: 2T and 4T. There are two functions available: normal cutting and metal mesh
cutting. The electrode and nozzle are more easily to wear out in metal mesh cutting.
3
)
Push the torch trigger on the cutting torch, the cutting machine works.
4
)
Set cutting current according to the thickness of workpiece.
5
)
Bring the copper nozzle of the cutting torch into contact with the workpiece
(
For models with
pilot arc function, keep a distance of about 2mm between the copper nozzle of the torch and the
workpiece.
)
, and then push the torch trigger. After the arc is ignited and started, raise the cutting
torch to the position about 1mm above the workpiece, and start cutting.
3.4 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it
will shorten the lifespan of the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece,
unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters
fly from the top of workpiece, it indicates that the workpiece can not be
fully cut because the cutting torch is moved too fast or the cutting current
is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance
between the nozzle and workpiece. If the torch is pressed against the
workpiece, the nozzle may stick to the workpiece, and smooth cutting
is unavailable.
For cutting round workpiece or to meet precise cutting requirement,
molding board or other assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check
if the arc is moving with the cutting line. If the space is not enough,
don’t bend the cable too much, step on or press upon the cable to avoid
suffocating of gas flow. The cutting torch may be burned because the
gas flow is too small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling
effect of the nozzle. Clean up the dust and spatters on the torch head
after using everyday to ensure good cooling effect.
11
3. OPERA
TION
3.3 Operation method
1
)
Turn on the power switch of the machine, and the power indicator illuminates.
2
)
Select proper working mode and proper function. There are two working modes available on
the machine panel: 2T and 4T. There are two functions available: normal cutting and metal mesh
cutting. The electrode and nozzle are more easily to wear out in metal mesh cutting.
3
)
Push the torch trigger on the cutting torch, the cutting machine works.
4
)
Set cutting current according to the thickness of workpiece.
5
)
Bring the copper nozzle of the cutting torch into contact with the workpiece
(
For models with
pilot arc function, keep a distance of about 2mm between the copper nozzle of the torch and the
workpiece.
)
, and then push the torch trigger. After the arc is ignited and started, raise the cutting
torch to the position about 1mm above the workpiece, and start cutting.
3.4 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it
will shorten the lifespan of the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece,
unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters
fly from the top of workpiece, it indicates that the workpiece can not be
fully cut because the cutting torch is moved too fast or the cutting current
is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance
between the nozzle and workpiece. If the torch is pressed against the
workpiece, the nozzle may stick to the workpiece, and smooth cutting
is unavailable.
For cutting round workpiece or to meet precise cutting requirement,
molding board or other assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check
if the arc is moving with the cutting line. If the space is not enough,
don’t bend the cable too much, step on or press upon the cable to avoid
suffocating of gas flow. The cutting torch may be burned because the
gas flow is too small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling
effect of the nozzle. Clean up the dust and spatters on the torch head
after using everyday to ensure good cooling effect.
11
3. OPERA
TION
3.3 Operation method
1
)
Turn on the power switch of the machine, and the power indicator illuminates.
2
)
Select proper working mode and proper function. There are two working modes available on
the machine panel: 2T and 4T. There are two functions available: normal cutting and metal mesh
cutting. The electrode and nozzle are more easily to wear out in metal mesh cutting.
3
)
Push the torch trigger on the cutting torch, the cutting machine works.
4
)
Set cutting current according to the thickness of workpiece.
5
)
Bring the copper nozzle of the cutting torch into contact with the workpiece
(
For models with
pilot arc function, keep a distance of about 2mm between the copper nozzle of the torch and the
workpiece.
)
, and then push the torch trigger. After the arc is ignited and started, raise the cutting
torch to the position about 1mm above the workpiece, and start cutting.
3.4 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it
will shorten the lifespan of the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece,
unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters
fly from the top of workpiece, it indicates that the workpiece can not be
fully cut because the cutting torch is moved too fast or the cutting current
is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance
between the nozzle and workpiece. If the torch is pressed against the
workpiece, the nozzle may stick to the workpiece, and smooth cutting
is unavailable.
For cutting round workpiece or to meet precise cutting requirement,
molding board or other assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check
if the arc is moving with the cutting line. If the space is not enough,
don’t bend the cable too much, step on or press upon the cable to avoid
suffocating of gas flow. The cutting torch may be burned because the
gas flow is too small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling
effect of the nozzle. Clean up the dust and spatters on the torch head
after using everyday to ensure good cooling effect.
11
3. OPERA
TION
3.3 Operation method
1
)
Turn on the power switch of the machine, and the power indicator illuminates.
2
)
Select proper working mode and proper function. There are two working modes available on
the machine panel: 2T and 4T. There are two functions available: normal cutting and metal mesh
cutting. The electrode and nozzle are more easily to wear out in metal mesh cutting.
3
)
Push the torch trigger on the cutting torch, the cutting machine works.
4
)
Set cutting current according to the thickness of workpiece.
5
)
Bring the copper nozzle of the cutting torch into contact with the workpiece
(
For models with
pilot arc function, keep a distance of about 2mm between the copper nozzle of the torch and the
workpiece.
)
, and then push the torch trigger. After the arc is ignited and started, raise the cutting
torch to the position about 1mm above the workpiece, and start cutting.
3.4 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it
will shorten the lifespan of the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece,
unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters
fly from the top of workpiece, it indicates that the workpiece can not be
fully cut because the cutting torch is moved too fast or the cutting current
is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance
between the nozzle and workpiece. If the torch is pressed against the
workpiece, the nozzle may stick to the workpiece, and smooth cutting
is unavailable.
For cutting round workpiece or to meet precise cutting requirement,
molding board or other assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check
if the arc is moving with the cutting line. If the space is not enough,
don’t bend the cable too much, step on or press upon the cable to avoid
suffocating of gas flow. The cutting torch may be burned because the
gas flow is too small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling
effect of the nozzle. Clean up the dust and spatters on the torch head
after using everyday to ensure good cooling effect.
11
3. OPERA
TION
3.3 Operation method
1
)
Turn on the power switch of the machine, and the power indicator illuminates.
2
)
Select proper working mode and proper function. There are two working modes available on
the machine panel: 2T and 4T. There are two functions available: normal cutting and metal mesh
cutting. The electrode and nozzle are more easily to wear out in metal mesh cutting.
3
)
Push the torch trigger on the cutting torch, the cutting machine works.
4
)
Set cutting current according to the thickness of workpiece.
5
)
Bring the copper nozzle of the cutting torch into contact with the workpiece
(
For models with
pilot arc function, keep a distance of about 2mm between the copper nozzle of the torch and the
workpiece.
)
, and then push the torch trigger. After the arc is ignited and started, raise the cutting
torch to the position about 1mm above the workpiece, and start cutting.
3.4 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it
will shorten the lifespan of the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece,
unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters
fly from the top of workpiece, it indicates that the workpiece can not be
fully cut because the cutting torch is moved too fast or the cutting current
is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance
between the nozzle and workpiece. If the torch is pressed against the
workpiece, the nozzle may stick to the workpiece, and smooth cutting
is unavailable.
For cutting round workpiece or to meet precise cutting requirement,
molding board or other assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check
if the arc is moving with the cutting line. If the space is not enough,
don’t bend the cable too much, step on or press upon the cable to avoid
suffocating of gas flow. The cutting torch may be burned because the
gas flow is too small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling
effect of the nozzle. Clean up the dust and spatters on the torch head
after using everyday to ensure good cooling effect.
11
3. OPERA
TION
3.3 Operation method
1
)
Turn on the power switch of the machine, and the power indicator illuminates.
2
)
Select proper working mode and proper function. There are two working modes available on
the machine panel: 2T and 4T. There are two functions available: normal cutting and metal mesh
cutting. The electrode and nozzle are more easily to wear out in metal mesh cutting.
3
)
Push the torch trigger on the cutting torch, the cutting machine works.
4
)
Set cutting current according to the thickness of workpiece.
5
)
Bring the copper nozzle of the cutting torch into contact with the workpiece
(
For models with
pilot arc function, keep a distance of about 2mm between the copper nozzle of the torch and the
workpiece.
)
, and then push the torch trigger. After the arc is ignited and started, raise the cutting
torch to the position about 1mm above the workpiece, and start cutting.
3.4 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it
will shorten the lifespan of the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece,
unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters
fly from the top of workpiece, it indicates that the workpiece can not be
fully cut because the cutting torch is moved too fast or the cutting current
is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance
between the nozzle and workpiece. If the torch is pressed against the
workpiece, the nozzle may stick to the workpiece, and smooth cutting
is unavailable.
For cutting round workpiece or to meet precise cutting requirement,
molding board or other assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check
if the arc is moving with the cutting line. If the space is not enough,
don’t bend the cable too much, step on or press upon the cable to avoid
suffocating of gas flow. The cutting torch may be burned because the
gas flow is too small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling
effect of the nozzle. Clean up the dust and spatters on the torch head
after using everyday to ensure good cooling effect.
11
3. OPERA
TION
3.3 Operation method
1
)
Turn on the power switch of the machine, and the power indicator illuminates.
2
)
Select proper working mode and proper function. There are two working modes available on
the machine panel: 2T and 4T. There are two functions available: normal cutting and metal mesh
cutting. The electrode and nozzle are more easily to wear out in metal mesh cutting.
3
)
Push the torch trigger on the cutting torch, the cutting machine works.
4
)
Set cutting current according to the thickness of workpiece.
5
)
Bring the copper nozzle of the cutting torch into contact with the workpiece
(
For models with
pilot arc function, keep a distance of about 2mm between the copper nozzle of the torch and the
workpiece.
)
, and then push the torch trigger. After the arc is ignited and started, raise the cutting
torch to the position about 1mm above the workpiece, and start cutting.
3.4 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it
will shorten the lifespan of the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece,
unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters
fly from the top of workpiece, it indicates that the workpiece can not be
fully cut because the cutting torch is moved too fast or the cutting current
is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance
between the nozzle and workpiece. If the torch is pressed against the
workpiece, the nozzle may stick to the workpiece, and smooth cutting
is unavailable.
For cutting round workpiece or to meet precise cutting requirement,
molding board or other assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check
if the arc is moving with the cutting line. If the space is not enough,
don’t bend the cable too much, step on or press upon the cable to avoid
suffocating of gas flow. The cutting torch may be burned because the
gas flow is too small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling
effect of the nozzle. Clean up the dust and spatters on the torch head
after using everyday to ensure good cooling effect.
copyrighted
document
- all
rights
reserved
by
FBC
