11
NL
M1.2.CUT80HFI.NLFREN 09102018
4�2 Werkmethode
1. Schakel de machine aan de hoofdschakelaar in. De spanningindicator licht op.
2. Selecteer de gewenste werkmodus en functie. Er zijn twee mogelijke werkmodi, die op het voorpaneel geselecteerd
kunnen worden: 2T en 4T. Er zijn twee mogelijke functies: normaal snijden en metaalgaas snijden. De elektrode en
het mondstuk verslijten sneller in de metaalgaas snijden modus.
3. Druk op de toortstrekker, de machine begint te werken.
4. Stel de stroomsterkte in, afhankelijk van de werkstukdikte.
5. Zet het koperen mondstuk in contact met het werkstuk (voor modellen met een pilootboog functie, houd een afstand
van ongeveer 2 mm tussen het mondstuk en het werkstuk), en druk op de toortstrekker. Wanneer de boog ontstoken
werd, til de snijtoorts op ongeveer 1 mm boven het werkstuk, en begin te snijden.
4�3 Aanbevelingen voor een correct snijden
Het is raadzaam de boog niet in de open lucht te ontsteken als het niet nodig is, omdat dit de
levensduur van de elektrode en van het mondstuk kan verminderen.
Het is raadzaam het snijden aan de hoek van het werkstuk te beginnen, tenzij een penetratie
vereist is.
Maak zeker dat de spatten vanaf de onderzijde van het werkstuk vliegen tijdens het snijden. Als
de spatten vanaf de bovenzijde van het werkstuk vliegen, betekent dit dat het werkstuk niet volledig
kan gesneden worden, of dat de toorts te snel bewogen wordt, of dat de snijstroom te laag is.
Houd het mondstuk lichtje in contact met het werkstuk, of laat een kleine afstand tussen het
mondstuk en het werkstuk. Als de toorts tegen het werkstuk gedrukt wordt, kan het mondstuk vast
blijven, en de snijding zal niet correct zijn.
Om een rond stuk of een precieze vorm te snijden, is het gebruik van een mal of ander accessoire
noodzakelijk.
Het is raadzaam de snijtoorts te trekken tijdens het snijden.
Houd het mondstuk of de toorts recht boven het werkstuk, en controleer of de boog met de snijlijn
beweegt. Als de ruimte niet voldoende is, pas op dat de kabel niet te strak geplooid wordt, en
dat u erop niet stapt of drukt, om de gasstroom niet te blokkeren. De toorts kan verbranden als de
gasstroom te laag is. Houd de snijkabel weg van werktuigen met scherpe kanten.
Verwijder de spatten van het mondstuk op tijd, omdat deze het afkoelen van het mondstuk kunnen
beïnvloeden. Verwijder de stof en spatten op de toortskop elke dag na gebruik, om een correcte
koeling te garanderen.
Het werkstuk is niet volledig gesneden� Mogelijke oorzaken:
• De snijstroom is te laag.
• De snijsnelheid is te hoog.
• De elektrode en het mondstuk zijn verbrand.
• Het werkstuk is te dik.
De slak druppelt vanaf de onderkant van het werkstuk� Mogelijke oorzaken:
• De snijsnelheid is te laag.
• De elektrode en het mondstuk zijn verbrand.
• De snijstroom is te hoog.
11
3. OPERA
TION
3.3 Operation method
1
)
Turn on the power switch of the machine, and the power indicator illuminates.
2
)
Select proper working mode and proper function. There are two working modes available on
the machine panel: 2T and 4T. There are two functions available: normal cutting and metal mesh
cutting. The electrode and nozzle are more easily to wear out in metal mesh cutting.
3
)
Push the torch trigger on the cutting torch, the cutting machine works.
4
)
Set cutting current according to the thickness of workpiece.
5
)
Bring the copper nozzle of the cutting torch into contact with the workpiece
(
For models with
pilot arc function, keep a distance of about 2mm between the copper nozzle of the torch and the
workpiece.
)
, and then push the torch trigger. After the arc is ignited and started, raise the cutting
torch to the position about 1mm above the workpiece, and start cutting.
3.4 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it
will shorten the lifespan of the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece,
unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters
fly from the top of workpiece, it indicates that the workpiece can not be
fully cut because the cutting torch is moved too fast or the cutting current
is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance
between the nozzle and workpiece. If the torch is pressed against the
workpiece, the nozzle may stick to the workpiece, and smooth cutting
is unavailable.
For cutting round workpiece or to meet precise cutting requirement,
molding board or other assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check
if the arc is moving with the cutting line. If the space is not enough,
don’t bend the cable too much, step on or press upon the cable to avoid
suffocating of gas flow. The cutting torch may be burned because the
gas flow is too small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling
effect of the nozzle. Clean up the dust and spatters on the torch head
after using everyday to ensure good cooling effect.
11
3. OPERA
TION
3.3 Operation method
1
)
Turn on the power switch of the machine, and the power indicator illuminates.
2
)
Select proper working mode and proper function. There are two working modes available on
the machine panel: 2T and 4T. There are two functions available: normal cutting and metal mesh
cutting. The electrode and nozzle are more easily to wear out in metal mesh cutting.
3
)
Push the torch trigger on the cutting torch, the cutting machine works.
4
)
Set cutting current according to the thickness of workpiece.
5
)
Bring the copper nozzle of the cutting torch into contact with the workpiece
(
For models with
pilot arc function, keep a distance of about 2mm between the copper nozzle of the torch and the
workpiece.
)
, and then push the torch trigger. After the arc is ignited and started, raise the cutting
torch to the position about 1mm above the workpiece, and start cutting.
3.4 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it
will shorten the lifespan of the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece,
unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters
fly from the top of workpiece, it indicates that the workpiece can not be
fully cut because the cutting torch is moved too fast or the cutting current
is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance
between the nozzle and workpiece. If the torch is pressed against the
workpiece, the nozzle may stick to the workpiece, and smooth cutting
is unavailable.
For cutting round workpiece or to meet precise cutting requirement,
molding board or other assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check
if the arc is moving with the cutting line. If the space is not enough,
don’t bend the cable too much, step on or press upon the cable to avoid
suffocating of gas flow. The cutting torch may be burned because the
gas flow is too small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling
effect of the nozzle. Clean up the dust and spatters on the torch head
after using everyday to ensure good cooling effect.
11
3. OPERA
TION
3.3 Operation method
1
)
Turn on the power switch of the machine, and the power indicator illuminates.
2
)
Select proper working mode and proper function. There are two working modes available on
the machine panel: 2T and 4T. There are two functions available: normal cutting and metal mesh
cutting. The electrode and nozzle are more easily to wear out in metal mesh cutting.
3
)
Push the torch trigger on the cutting torch, the cutting machine works.
4
)
Set cutting current according to the thickness of workpiece.
5
)
Bring the copper nozzle of the cutting torch into contact with the workpiece
(
For models with
pilot arc function, keep a distance of about 2mm between the copper nozzle of the torch and the
workpiece.
)
, and then push the torch trigger. After the arc is ignited and started, raise the cutting
torch to the position about 1mm above the workpiece, and start cutting.
3.4 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it
will shorten the lifespan of the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece,
unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters
fly from the top of workpiece, it indicates that the workpiece can not be
fully cut because the cutting torch is moved too fast or the cutting current
is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance
between the nozzle and workpiece. If the torch is pressed against the
workpiece, the nozzle may stick to the workpiece, and smooth cutting
is unavailable.
For cutting round workpiece or to meet precise cutting requirement,
molding board or other assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check
if the arc is moving with the cutting line. If the space is not enough,
don’t bend the cable too much, step on or press upon the cable to avoid
suffocating of gas flow. The cutting torch may be burned because the
gas flow is too small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling
effect of the nozzle. Clean up the dust and spatters on the torch head
after using everyday to ensure good cooling effect.
11
3. OPERA
TION
3.3 Operation method
1
)
Turn on the power switch of the machine, and the power indicator illuminates.
2
)
Select proper working mode and proper function. There are two working modes available on
the machine panel: 2T and 4T. There are two functions available: normal cutting and metal mesh
cutting. The electrode and nozzle are more easily to wear out in metal mesh cutting.
3
)
Push the torch trigger on the cutting torch, the cutting machine works.
4
)
Set cutting current according to the thickness of workpiece.
5
)
Bring the copper nozzle of the cutting torch into contact with the workpiece
(
For models with
pilot arc function, keep a distance of about 2mm between the copper nozzle of the torch and the
workpiece.
)
, and then push the torch trigger. After the arc is ignited and started, raise the cutting
torch to the position about 1mm above the workpiece, and start cutting.
3.4 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it
will shorten the lifespan of the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece,
unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters
fly from the top of workpiece, it indicates that the workpiece can not be
fully cut because the cutting torch is moved too fast or the cutting current
is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance
between the nozzle and workpiece. If the torch is pressed against the
workpiece, the nozzle may stick to the workpiece, and smooth cutting
is unavailable.
For cutting round workpiece or to meet precise cutting requirement,
molding board or other assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check
if the arc is moving with the cutting line. If the space is not enough,
don’t bend the cable too much, step on or press upon the cable to avoid
suffocating of gas flow. The cutting torch may be burned because the
gas flow is too small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling
effect of the nozzle. Clean up the dust and spatters on the torch head
after using everyday to ensure good cooling effect.
11
3. OPERA
TION
3.3 Operation method
1
)
Turn on the power switch of the machine, and the power indicator illuminates.
2
)
Select proper working mode and proper function. There are two working modes available on
the machine panel: 2T and 4T. There are two functions available: normal cutting and metal mesh
cutting. The electrode and nozzle are more easily to wear out in metal mesh cutting.
3
)
Push the torch trigger on the cutting torch, the cutting machine works.
4
)
Set cutting current according to the thickness of workpiece.
5
)
Bring the copper nozzle of the cutting torch into contact with the workpiece
(
For models with
pilot arc function, keep a distance of about 2mm between the copper nozzle of the torch and the
workpiece.
)
, and then push the torch trigger. After the arc is ignited and started, raise the cutting
torch to the position about 1mm above the workpiece, and start cutting.
3.4 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it
will shorten the lifespan of the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece,
unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters
fly from the top of workpiece, it indicates that the workpiece can not be
fully cut because the cutting torch is moved too fast or the cutting current
is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance
between the nozzle and workpiece. If the torch is pressed against the
workpiece, the nozzle may stick to the workpiece, and smooth cutting
is unavailable.
For cutting round workpiece or to meet precise cutting requirement,
molding board or other assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check
if the arc is moving with the cutting line. If the space is not enough,
don’t bend the cable too much, step on or press upon the cable to avoid
suffocating of gas flow. The cutting torch may be burned because the
gas flow is too small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling
effect of the nozzle. Clean up the dust and spatters on the torch head
after using everyday to ensure good cooling effect.
11
3. OPERA
TION
3.3 Operation method
1
)
Turn on the power switch of the machine, and the power indicator illuminates.
2
)
Select proper working mode and proper function. There are two working modes available on
the machine panel: 2T and 4T. There are two functions available: normal cutting and metal mesh
cutting. The electrode and nozzle are more easily to wear out in metal mesh cutting.
3
)
Push the torch trigger on the cutting torch, the cutting machine works.
4
)
Set cutting current according to the thickness of workpiece.
5
)
Bring the copper nozzle of the cutting torch into contact with the workpiece
(
For models with
pilot arc function, keep a distance of about 2mm between the copper nozzle of the torch and the
workpiece.
)
, and then push the torch trigger. After the arc is ignited and started, raise the cutting
torch to the position about 1mm above the workpiece, and start cutting.
3.4 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it
will shorten the lifespan of the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece,
unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters
fly from the top of workpiece, it indicates that the workpiece can not be
fully cut because the cutting torch is moved too fast or the cutting current
is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance
between the nozzle and workpiece. If the torch is pressed against the
workpiece, the nozzle may stick to the workpiece, and smooth cutting
is unavailable.
For cutting round workpiece or to meet precise cutting requirement,
molding board or other assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check
if the arc is moving with the cutting line. If the space is not enough,
don’t bend the cable too much, step on or press upon the cable to avoid
suffocating of gas flow. The cutting torch may be burned because the
gas flow is too small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling
effect of the nozzle. Clean up the dust and spatters on the torch head
after using everyday to ensure good cooling effect.
11
3. OPERA
TION
3.3 Operation method
1
)
Turn on the power switch of the machine, and the power indicator illuminates.
2
)
Select proper working mode and proper function. There are two working modes available on
the machine panel: 2T and 4T. There are two functions available: normal cutting and metal mesh
cutting. The electrode and nozzle are more easily to wear out in metal mesh cutting.
3
)
Push the torch trigger on the cutting torch, the cutting machine works.
4
)
Set cutting current according to the thickness of workpiece.
5
)
Bring the copper nozzle of the cutting torch into contact with the workpiece
(
For models with
pilot arc function, keep a distance of about 2mm between the copper nozzle of the torch and the
workpiece.
)
, and then push the torch trigger. After the arc is ignited and started, raise the cutting
torch to the position about 1mm above the workpiece, and start cutting.
3.4 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it
will shorten the lifespan of the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece,
unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters
fly from the top of workpiece, it indicates that the workpiece can not be
fully cut because the cutting torch is moved too fast or the cutting current
is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance
between the nozzle and workpiece. If the torch is pressed against the
workpiece, the nozzle may stick to the workpiece, and smooth cutting
is unavailable.
For cutting round workpiece or to meet precise cutting requirement,
molding board or other assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check
if the arc is moving with the cutting line. If the space is not enough,
don’t bend the cable too much, step on or press upon the cable to avoid
suffocating of gas flow. The cutting torch may be burned because the
gas flow is too small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling
effect of the nozzle. Clean up the dust and spatters on the torch head
after using everyday to ensure good cooling effect.
11
3. OPERA
TION
3.3 Operation method
1
)
Turn on the power switch of the machine, and the power indicator illuminates.
2
)
Select proper working mode and proper function. There are two working modes available on
the machine panel: 2T and 4T. There are two functions available: normal cutting and metal mesh
cutting. The electrode and nozzle are more easily to wear out in metal mesh cutting.
3
)
Push the torch trigger on the cutting torch, the cutting machine works.
4
)
Set cutting current according to the thickness of workpiece.
5
)
Bring the copper nozzle of the cutting torch into contact with the workpiece
(
For models with
pilot arc function, keep a distance of about 2mm between the copper nozzle of the torch and the
workpiece.
)
, and then push the torch trigger. After the arc is ignited and started, raise the cutting
torch to the position about 1mm above the workpiece, and start cutting.
3.4 Notes for cutting operation
It is recommended not to ignite the arc in the air if not necessary, for it
will shorten the lifespan of the electrode and nozzle of the torch.
It is recommended to initiate the cutting from the edge of workpiece,
unless penetration is needed.
Ensure spatters fly from the bottom of workpiece while cutting. If spatters
fly from the top of workpiece, it indicates that the workpiece can not be
fully cut because the cutting torch is moved too fast or the cutting current
is too low.
Keep the nozzle slightly touching the workpiece or keep a short distance
between the nozzle and workpiece. If the torch is pressed against the
workpiece, the nozzle may stick to the workpiece, and smooth cutting
is unavailable.
For cutting round workpiece or to meet precise cutting requirement,
molding board or other assistant tools are needed.
It is recommended to pull the cutting torch while cutting.
Keep the nozzle of cutting torch upright over the workpiece, and check
if the arc is moving with the cutting line. If the space is not enough,
don’t bend the cable too much, step on or press upon the cable to avoid
suffocating of gas flow. The cutting torch may be burned because the
gas flow is too small. Keep the cutting cable away from edge tools.
Clean up the spatters on the nozzle timely, for it will affect the cooling
effect of the nozzle. Clean up the dust and spatters on the torch head
after using everyday to ensure good cooling effect.
copyrighted
document
- all
rights
reserved
by
FBC
