Volvo EPA2007 D13F Reference Manual Download Page 58

Page: 58 / 179

52 SPECIFICATIONS

Engine Lubricants and Sealants

Use only the following recommended sealing compounds and lubricants.

Note:

All genuine cylinder head gaskets are pre-coated and do not require any type of

sealing compound. When installing new gaskets, clean and degrease gasket sealing
surfaces to avoid leaks.

Location

Sealant or Lubricant

Cup plugs/threaded plugs

Loctite® 277 or equivalent / Teflon®
thread sealer

Cylinder liner seat

1161231 sealant

Oil filter seal

Clean engine oil

Holding metal parts in place

Petroleum jelly

Valve stems and guides

Clean engine oil

Engine front cover/flywheel
housing/timing gear cover

3092340 sealant

Engine parts, fasteners and washers

Clean engine oil

Exhaust manifold studs

High temperature 1161929 anti-seize

Oil cooler assembly O-ring

Clean engine oil

O-rings, coolant, EPDM

Clean coolant, or Dow Corning® 55

O-rings (except as noted)

Dow Corning® 55 O-ring lubricant

Threaded sensors

Sealing compound on threads

Turbocharger mounting nuts

1161929 anti-seize

Note: All part numbers are for
reference only, you should always refer
to truck BOM’s before ordering parts.

Summary of Contents for EPA2007 D13F




















































































































































































Search results

Summary of Contents for EPA2007 D13F

Reviews:

Related manuals for EPA2007 D13F

Brands by name

Popular brands

Volvo EPA2007 D13F, Reference Manual

Search results

Summary of Contents for EPA2007 D13F

Reviews:

Related manuals for EPA2007 D13F

Brands by name

Popular brands