Volvo EPA2007 D13F Reference Manual Download Page 148

Page: 148 / 179

142 BASIC SERVICE

Note:

VCS coolant is used to protect the cooling system.

Remove and Replace

1 Close the shut-off valve on the coolant pump housing.

Note:

In the closed position, the pin on the shut-off valve should be horizontal.

2 Place a suitable container below the filter to collect spilled coolant.

3 Using filter wrench J 48061 or equivalent, unscrew the filter and discard it safely.

4 Apply a light film of coolant on the face of the new filter gasket.

5 Screw the new filter on the threaded nipple extending from the mounting flange.

6 Using the filter wrench, tighten the filter one full turn after the gasket contacts

the base.

7 Open the shut-off valve on the coolant pump housing.

8 Check for any coolant leaks.

Summary of Contents for EPA2007 D13F




















































































































































































Search results

Summary of Contents for EPA2007 D13F

Reviews:

Related manuals for EPA2007 D13F

Brands by name

Popular brands

Volvo EPA2007 D13F, Reference Manual

Search results

Summary of Contents for EPA2007 D13F

Reviews:

Related manuals for EPA2007 D13F

Brands by name

Popular brands