Volvo EPA2007 D13F Reference Manual Download Page 94 | Manualshive

Page: 94 / 179

background image

88 ENGINE COMPONENT AND LOCATION

Timing Gears

W2033318

1. Crankshaft Gear

6. Power Steering/Fuel Pump Gear

2. Double Idler Gear

7. Air Compressor Gear

3. Adjustable Idler Gear

8. Oil Pump Gear

4. Camshaft Gear and Damper

9. Power Take-Off Gear (Optional)

5. Auxiliary Idler Gear

10. Timing Gear Plate

The timing gears are located at the rear of the engine. Backing up the gears is a plate:
a 6 mm (1/4 inch) thick steel sheet attached to the cylinder block.

The advantages of this configuration are more precise timing, fewer components
and lower noise levels.

The power steering/fuel pump gear, the air compressor gear and the PTO gear are not
timing gears. The pump and compressor gears fasten to their respective components.
The pump gear is driven by the auxiliary idler gear. The compressor gear is driven
by the double idler gear.

The double idler drives the adjustable idler and the gear used to drive the power
take-off, if so equipped. This is part of the "REPTO-Ready" feature. A PTO unit with
drive gear is substituted for a cover on the flywheel housing.

The camshaft gear fastens to the hub on the end of the shaft. A vibration damper also
attaches to the hub outboard of the gear. Teeth on the damper actuate the camshaft
position sensor. The gear is driven via the adjustable idler.

«
...
92
93
94
95
96
...
»

Summary of Contents for EPA2007 D13F




















































































































































































Reviews:

No comments

Related manuals for EPA2007 D13F

Brand: BAFANG Pages: 4

Brand: VEM Pages: 27

Brand: Jacobsen Pages: 103

Brand: Westerbeke Pages: 112

Brand: Isuzu Pages: 174

Brand: Lenze Pages: 64

Brand: TYROLIT Hydrostress Pages: 19

Brand: AL-KO Pages: 144

Brand: Moons' Pages: 28

Brand: Nissei Pages: 16

Brand: Lenze Pages: 36

Brand: Deutz Pages: 37

Brand: CHERUBINI Pages: 24

Brand: ACDC Pages: 20

Brand: MTU Pages: 187

Brand: Iveco Motors Pages: 60

Brand: Iveco Pages: 206

PowerBuilt Snow 120000 Series

Brand: Briggs & Stratton Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands