Volvo EPA2007 D13F Reference Manual Download Page 163 | Manualshive

Page: 163 / 179

background image

BASIC SERVICE 157

W2033389

9. Inspect the injector tip to make sure it is thoroughly clean and all soot has been
removed. Use a mirror if a clear view of the tip is not possible.

10. Install a new high-temperature gasket and steel plate gasket onto the bottom of
the aftertreatment fuel injector.

11. Apply high-temperature nickel-graphite anti-seize compound to the new injector
mounting bolt threads and insert the bolts into the spacers. Position the injector onto
the diffuser pipe (which attaches to the turbocharger outlet) and hand start the bolts
with spacers.

12. Secure the injector mounting bolts. Tighten the bolts according to specification.

W2005656

13. Connect the aftertreatment fuel injector fuel supply line and tighten to
specification.

14. Install P-clamp bolts to secure the AFI harness and fuel line.

15. Connect all previously disconnected cables to the ground (negative) battery
terminals.

16. Using VCADS/ Premium Tech Tool, (PTT) reset the AFI adaptive factor, clear
codes and test the system for proper operation.

«
...
161
162
163
164
165
...
»

Summary of Contents for EPA2007 D13F




















































































































































































Reviews:

No comments

Related manuals for EPA2007 D13F

Brand: Paccar Pages: 71

Brand: DAF Pages: 87

Vanguard 540000 Series

Brand: Briggs & Stratton Pages: 32

Pad-Mounted Series

Brand: S&C Pages: 15

Jeep Six-Cylinder

Brand: Golen Pages: 11

LYCOMING 200-6XL Series

Brand: E-MAG Pages: 30

Brand: Westerbeke Pages: 140

StarDental Titan-E

Brand: DentalEZ Pages: 2

Brand: Transtecno Pages: 10

WEST EUROTECH 36 T2

Brand: Weston UK Pages: 3

Brand: Craftsman Pages: 48

Brand: Craftsman Pages: 48

Brand: Newland Pages: 29

Brand: GR Pages: 8

Brand: Northern Lights Pages: 36

Brand: Northern Lights Pages: 45

Brand: Northern Lights Pages: 56

Brand: FUTABA Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands