Volvo EPA2007 D13F Reference Manual Download Page 145 | Manualshive

Page: 145 / 179

background image

BASIC SERVICE 139

Fuel Filter Replacement

Note:

Because of ice buildup or fuel waxing which can clog fuel filters, it may be

necessary during extremely cold weather to reduce the time or mileage interval
between fuel filter changes.
Be careful to prevent foreign matter of any kind from entering the filters during
service.
Install new fuel filters dry.

Water Separating Pre-Filter Replacement

To replace the water separating pre-filter:

1 Disconnect the electrical cable.

2 Make sure the filter casing is thoroughly cleaned. If not already done, wash the

area around the filter mounting adapter with a suitable solvent and blow dry with
compressed air.

3 With a suitable container in place to collect spillage, open the fitting and drain

the filter.

4 Unscrew and remove the water cup.

5 Using a filter wrench, remove the filter from the mounting bracket and discard

it safely.

6 Apply a thin film of clean engine oil to the sealing gasket of the new filter.

7 Screw the new dry filter in place and tighten an additional 3/4 to 1 turn by hand

after the gasket contacts the base.

8 Screw the water cup into the filter casing.

Note:

There is a new-style pre-filter with a stepped-down diameter at the bottom

of the filter. The earlier-style filter has straight sides with a larger bottom diameter
which requires an adapter to attach the fuel/water separator bowl to the filter. When
replacing the previous straight-sided filter with the current stepped-down version,
the adapter is not used. However, do not discard the adapter as it can be used
should inventory of the earlier-style filter still be available.

9 If necessary, replace the full-flow main filter. See the following instructions.

10 Connect the electrical cable.

11 Start the engine and run at idle for five minutes to fill the filter with fuel.

12 Check for leaks.

«
...
143
144
145
146
147
...
»

Summary of Contents for EPA2007 D13F




















































































































































































Reviews:

No comments

Related manuals for EPA2007 D13F

Char-Lynn 2000 Series

Brand: Eaton Pages: 18

MTR-DCI-...IO Series

Brand: Festo Pages: 182

Brand: Lister Petter Pages: 81

Brand: Lister Petter Pages: 100

Brand: FUTABA Pages: 2

Brand: Chicago Electric Pages: 8

Brand: DLE Pages: 4

Brand: DLE Pages: 24

Brand: Honda Pages: 45

Brand: Mitsubishi Pages: 79

Brand: Honda Pages: 2

Brand: Honda Pages: 32

Brand: Honda Pages: 56

Brand: Mitsubishi Pages: 116

Brand: O.S. engine Pages: 40

Brand: M.T.H. Pages: 28

Brand: Roma Pages: 2

Brand: PrimaLuceLab Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands