Volvo EPA2007 D13F Reference Manual Download Page 159 | Manualshive

Page: 159 / 179

background image

BASIC SERVICE 153

W2033386

6. Disconnect both the inlet and outlet coolant lines from the aftertreatment fuel
injector fittings.

7. Disconnect the aftertreatment fuel injector wiring harness connector. Remove all
clips and tie straps to allow the harness to hang free.

8. Remove and discard the aftertreatment fuel injector mounting bolts and spacers,
and then remove the injector from the diffuser pipe attached to the turbocharger outlet.

Note:

Mark the AFI orientation relationship to the diffuser. With the early-style

diffuser, the AFI is positioned with the higher side of the AFI heat shield facing the
turbocharger. With the new-style diffuser, the AFI is positioned with the higher side
of the heat shield facing the EGR valve.

9. Remove and discard the high-temperature gasket and steel plate gasket from the
bottom of the injector.

Installation

1. Install a new high-temperature gasket and steel plate gasket onto the bottom of
the aftertreatment fuel injector.

2. Apply high-temperature nickel-graphite anti-seize compound to new injector
mounting bolt threads and insert the bolts into the spacers. Position the injector onto
the diffuser pipe (attached to the turbocharger outlet) and hand start the bolts with
spacers.

Note:

Install the AFI as marked at disassembly.

«
...
157
158
159
160
161
...
»

Summary of Contents for EPA2007 D13F




















































































































































































Reviews:

No comments

Related manuals for EPA2007 D13F

Brand: Quectel Pages: 71

Brand: O.S. engine Pages: 19

Brand: GRITAL Pages: 4

Brand: Cadillac Pages: 36

Brand: Perkins Pages: 42

Brand: SOMFY Pages: 48

Brand: Siemens Pages: 4

SIMOTICS A-1FV5

Brand: Siemens Pages: 66

Brand: Siemens Pages: 56

SIMODRIVE POSMO A

Brand: Siemens Pages: 58

Brand: Siemens Pages: 100

Simotics HV C 1NA14544WA600AG0-Z

Brand: Siemens Pages: 112

SIMOTICS DP 1PC13

Brand: Siemens Pages: 100

SIMOTICS DP 1PC134

Brand: Siemens Pages: 120

SIMOTICS HT Series

Brand: Siemens Pages: 128

Brand: Siemens Pages: 136

SIMOTICS DC 1GH5

Brand: Siemens Pages: 130

SIMOTICCS A 1FU9

Brand: Siemens Pages: 126

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands