Volvo EPA2007 D13F Reference Manual Download Page 166 | Manualshive

Page: 166 / 179

background image

160 BASIC SERVICE

General Information

W2033396

Timing marks for basic camshaft timing and adjustment of the valves and unit
injectors are located at the front of the camshaft just forward of the No. 1 front bearing
journal. Two lines at the top of the front bearing cap mark the alignment point for
positioning of the camshaft and making the adjustments.

The top dead center (TDC) mark is used for basic camshaft timing. The TDC mark
must be between the two lines on the front camshaft bearing cap when the flywheel is
at 0° (top dead center for cylinder No. 1).

The engine must be cold, 60°C (140°F) or less, before making these adjustments.

Camshaft markings for setting of valves and unit injectors:

•

Without Volvo Engine Brake

: Markings 1–6 apply to adjustment of inlet valves,

exhaust valves and injectors.

•

With Volvo Engine Brake

: Markings 1–6 apply to adjustment of inlet valves and

injectors. Markings E1–E6 apply to adjustment of exhaust valves.

«
...
164
165
166
167
168
...
»

Summary of Contents for EPA2007 D13F




















































































































































































Reviews:

No comments

Related manuals for EPA2007 D13F

RailKing RKS SD70ACE

Brand: M.T.H. Pages: 12

Viper Engines 31321

Brand: Ardisam Pages: 20

Brand: Nanni Pages: 13

Brand: Indmar Pages: 94

Brand: MAK Pages: 2027

Brand: Vanguard Pages: 120

Brand: Kuda Pages: 98

Brand: GAPOSA Pages: 2

Brand: King Canada Pages: 8

Brand: Fabtex Pages: 4

Brand: Emerson Pages: 18

Brand: Emerson Pages: 124

Leroy-Somer FFB

Brand: Emerson Pages: 12

Brand: Bison Pages: 19

dunkermotoren D258

Brand: Ametek Pages: 8

Brand: Chicago Pneumatic Pages: 100

TWINMOT T2-PLUS H

Brand: Germany Motions Pages: 12

Brand: Yanmar Pages: 84

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands