Volvo Penta D16 Operator'S Manual Download

Page: 46 / 90

Sd Overspeed SDU

Wrn ECU, Wrn J1587

Critical system fault Engine shuts down automatically.
Contact a Volvo Penta workshop if the fault remains.

Secondary Batt Fls

Secondary Battery.
Poor batteries or charging Refer to

Battery, Charging

SeaWater Press Wrn

Seawater pressure too low Engine power is reduced.

• Check that the seawater filter is not blocked., Refer to

Seawater Filter, Check and Cleaning, page 72

• Check the impeller in the sea water pump. Refer to

Impeller, Check and Change, page 71

• Check that no leakage occurs.

Water in fuel Wrn

Water in Fuel.

• Empty the water trap underneath the fuel filters. Refer to

Fuel pre-filter with water separator

Wrn

Miscellaneous system faults
Engine performance can be affected. Several possible causes of engine problems are described below.

• Battery voltage incorrect

Check belt tension. Refer to

Drive belt, check and change, page 56

Check battery fluid level. Refer to

Battery, page 74

• Fuel pressure incorrect.

Engine performance can be affected.

• Communication failure

Gear automatically set to neutral. Engine performance can be affected.

• Oil pressure too low.

Engine power is reduced.
Check the oil level in the engine. Refer to

Oil level, checking and topping up, page 57

Check that no leakage occurs.

Wrn Derate Alarm

Engine performance can be affected. Several possible causes of engine problems are described below.

• Battery voltage incorrect

Check belt tension. Refer to

Drive belt, check and change, page 56

Check battery fluid level. Refer to

Battery, page 74

• Fuel pressure incorrect. Engine performance can be affected.

• Oil pressure too low. Engine power is reduced.

Checking Engine Oil Level. Refer to

Oil level, checking and topping up, page 57

Check that no leakage occurs.

Contact a Volvo Penta workshop if the fault remains.

Fault Code Register

47711740 05-2019 © AB VOLVO PENTA

Summary of Contents for D16



























































































Search results

Summary of Contents for D16

Reviews:

Related manuals for D16

Brands by name

Popular brands

Volvo Penta D16, Operator'S Manual

Search results

Summary of Contents for D16

Reviews:

Related manuals for D16

Brands by name

Popular brands