Volvo Penta D16 Operator'S Manual Download | Manualshive

Page: 51 / 90

background image

Maintenance

This chapter contains general technical information and instructions on how the common maintenance items that
must be carried out. Read through the instructions carefully before starting work.
Read through the safety precautions for maintenance and service in the

Safety precautions for maintenance and

service operations

chapter before work on the engine is begun.

Volvo Penta recommend that all servicing with the engine running should be undertaken by an authorized Volvo
Penta workshop. The intervals when maintenance items must be carried are indicated in the

Maintenance

Schedule

.

WARNING!

Care and maintenance work should be done with the engine stopped unless otherwise specified. Stop the engine
before opening or removing the engine hatch/hood. Make it impossible to start the engine by removing the start
key and cutting the system voltage with the main switches.

NOTICE!

More information on how to perform service and maintenance can be found in the

Service and

Maintenance handbook

. The manual is available for download at www.volvopenta.com.

D16 HE

P0010383

1 Electrical connection box with SD reset

2 Expansion tank

3 Heat exchanger

4 Coolant filler cap

5 Auxiliary stop

6 Oil filler cap, engine

7 Switchable fuel filters

8 Seawater Pump

9 Fuel Shut-off Valve

10 Engine Control Unit

11 Alternator

12 Charge air cooler

13 Air Filter

14 Fresh water pump

15 Oil filter

16 By-pass filter for engine oil

17 Starter motor

47711740 05-2019 © AB VOLVO PENTA

49

«
...
49
50
51
52
53
...
»

Summary of Contents for D16



























































































Reviews:

No comments

Related manuals for D16

Brand: Canaline Engines Pages: 39

Brand: Kohler Pages: 116

Brand: Beta Marine Pages: 88

EC FSE 400 - SERVICE 2002 & 2003

Brand: GAS GAS Pages: 74

Brand: Parker Pages: 20

Brand: Jenny Science Pages: 9

Brand: MTU Pages: 163

Brand: MINN KOTA Pages: 42

Brand: Louvolite Pages: 4

IntelliGear Plus

Brand: Browning Pages: 20

Brand: Chicago Pneumatic Pages: 100

Brand: DETROIT Pages: 84

Brand: Detroit Diesel Pages: 116

Brand: Detroit Diesel Pages: 158

Brand: Detroit Diesel Pages: 172

Brand: Stober Pages: 48

MAX-37SZ-H RING

Brand: O.S. engine Pages: 4

Brand: O.S. engine Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands