Volvo Penta D16 Operator'S Manual Download | Manualshive

Page: 79 / 90

background image

Storage

The engine and other equipment must be laid up to prevent damage if they are not used for two months or more.
It is important that this is done in the correct manner, and nothing is forgotten. For this reason, we have compiled
a check list of the most important points.
Before the engine is taken out of service for a long period of time, an authorized Volvo Penta workshop should
check it over. Have any faults and deficiencies attended to, so that the equipment is in order, ready for the next
start.

CAUTION!

Read the chapter on Maintenance in the Operator`s Manual before starting work. It contains instructions on how
to carry out maintenance and service operations in a safe and technical correct manner.

WARNING!

Conservations oils can be flammable and dangerous to inhale. Ensure good ventilation. Use a protective face
mask when spraying.

IMPORTANT:

When cleaning with a high pressure washer, make sure to never aim the water jet at seals, rubber hoses or
electrical components.

•

For up to 8 month’s stoppage:

Change the oil and oil filter on the engine, then warm
it up afterwards.

More than 8 month's stoppage:

Conserve the lubrication and fuel systems with
conservation oil. Please refer section

Storage, page 78

.

•

Check that the coolant offers sufficient freeze
protection. Top up as necessary.
Alternatively, you can drain the coolant (also drain
the coolant filter).

•

Drain any water and contamination from the fuel
filters and fuel tank. Fill the fuel tank completely, to
avoid condensation.

•

Disconnect the battery cables, clean and charge the
batteries. Trickle charge the batteries while the
equipment is in storage. A poorly charged battery
can freeze and burst.

•

Clean the outside of the engine. Do not use a high
pressure washer for engine cleaning. Touch up
paint damage with Volvo Penta original paint.

•

Check and rust-proof any control cables.

•

Put a note on the engine with the date, type of
conservation and the conservation oil used.

•

Cover over the air filter, exhaust pipe and engine if
necessary.

47711740 05-2019 © AB VOLVO PENTA

77

«
...
77
78
79
80
81
...
»

Summary of Contents for D16



























































































Reviews:

No comments

Related manuals for D16

Brand: RCGF Pages: 22

Brand: Northern Lights Pages: 31

Brand: Kohler Pages: 109

44 A FOUR-35C THREE

Brand: Westerbeke Pages: 61

Brand: GGP Pages: 56

Brand: CAB Pages: 16

Brand: Willys Pages: 77

Brand: DUROMAX Pages: 32

Brand: aFe Power Pages: 16

Brand: Wilesco Pages: 4

GMC 6.6L Duramax Diesel 2020

Brand: Chevrolet Pages: 96

ZA top SM200.40E

Brand: ZIEHL-ABEGG Pages: 64

Brand: Wood-mizer Pages: 12

Brand: Mitsubishi Pages: 216

Brand: Mitsubishi Pages: 3

Brand: Sabre Pages: 30

Brand: Performance Pages: 21

Brand: California Air Tools Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands